KMD-460 & 530M_H:
Loosen the two thumbscrews on the pump insulation
panel (B) and remove the panel.
Disconnect the discharge hose, the drain valve hose,
and the overflow drain hose.
Disconnect the pump motor and then the float switch
connectors from the control board.
Remove the two thumbscrews securing the pump
motor and float switch assembly.
Pull out the water tank, cube guide, and pump motor
and float switch assembly all together.
Remove the screw securing the float switch to the
top of the assembly, remove the float switch*.
See Step
for cleaning steps. Reassemble in the
reverse order they were removed.
* Remove retainer rod (take care not to bend excessively) from bottom of the float switch housing & clean all float parts.
Replace all the
Panels,
except the
Front Panel
.
Move the
service switch
to
WASH
, and the
control
switch
to
SERVICE
. Replace the
Front Panel
.
After
30 minutes
, remove the
Front Panel
, move
the
service switch
to
DRAIN
. Replace the
Front
Panel
.
ATTENTION!
To prevent damage to the water pump,
do not leave the control switch on SERVICE for
extended periods when water tank is empty.
Cleaning Rinse:
After
2 minutes
, remove the
Front Panel
, move the
control switch
to
ICE
. Replace
the
Front Panel
.
After
3 minutes
, move the
service switch
to
WASH
, and the
control switch
to
SERVICE
. Replace the
Front Panel
.
After
5 minutes
, remove the
Front Panel
, move the
service switch
to
DRAIN
.
Replace the
Front Panel
After
2 minutes
, remove the
Front Panel
, move the
control switch
to
OFF
.
Repeat 3x
(Steps
༗
thru
༚
)
to rinse thoroughly. Continue to
Sanitation – Step
༜
on front
...
භ
Scoop
භ
Water Filters
භ
Exterior
භ
Bin Door/Top Kit
භ
Icemaker/Bin
භ
Water Supply Inlet
භ
Condenser
භ
Water Hoses
Dish soap, rinse well
Check psi, change if req’d
Dish soap & damp cloth
Warm water & clean cloth
Follow these instructions
Clean inlet screen
Inspect. Clean with brush
Inspect. Replace if req’d
භ
භ
භ
Tech Support: 1.800.233.1940
Page 2
#51009 | 4.28.2017
!
sanitizing continued…
RINSE 1:
(Steps 20-22)
x
Move
control switch
to ICE,
replace front panel
x
After 3 minutes, remove the
front panel
x
Move
service switch
to WASH
and
control switch
to SERVICE,
replace the front panel
x
After 5 minutes, remove the
front panel
x
Move
service switch
to DRAIN,
replace the front panel
x
After 2 minutes, remove
the front panel
x
Move
control switch
to OFF,
replace the front panel
RINSE 2:
x
Repeat RINSE 1 (Steps 20–22)
for complete ice/food safety
x
Clean the dispenser unit /
ice storage bin liner with a
neutral cleaner (dish soap)
x
Rinse thoroughly
x
Move
control switch
to ICE,
replace front panel
R
M
8
A
9
A
10
A
11
A
12
AMMONIA
Cleaners
20
e
21
22
23
,
25
24
Need Service or Repair? Locate your closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-rep
After
30 min.
A
13
R
14
After
2 min.
After
3 min.
DO NOT
use ammonia type cleaners
WEAR
liquid-proof gloves and goggles
to protect skin & eyes from cleaning &
sanitizing chemicals
DO NOT
use ammonia type cleaners
ATTENTION!
IF ICEMAKER IS ON DISPENSER,
remember to turn on the dispenser
after cleaning
KMD-410M_H:
Loosen the two thumbscrews securing the
pump motor bracket.
Disconnect the discharge hose.
Disconnect the pump motor and float switch
connectors from the side of the control box.
While pushing up on the snap tab, pull out the
water tank, cube guide, pump motor bracket,
and pump motor and float switch assembly all
together.
Remove the pump motor bracket securing the
float switch to the top of the assembly, remove
the float switch*.
See Step
for cleaning steps. Reassemble in
the reverse order they were removed.
co
Re
m
Pu
an
Re
to
Se
re
FLOAT S
W
ITCH CLE
ANING
After
5 min.
After
3 min.
Repeat
3x
Page 9
