background image

Timeswitch specification 
CentaurPlus ZW

Contact Rating 3 (1) Amps 230V AC

Contact Type Micro-disconnection changeover

Voltage free

Supply 230V AC 50Hz only

Pollution Degree 2

Impulse Voltage Rating 2500V

Class A Software Type 1 Control

Operating Temperature Range 0 °C to +40 °C

Battery  Life  10  months  continuous  operation 
(minimum)

Case Material Thermoplastic, flame retardant

Ball Pressure Test Temperature 75 °C

Dimensions 84mm x 150mm x 29mm

Display Back lit liquid crystal

Clock 12 hour AM/PM

Auto BST/GMT changeover

Displayed  Time  adjustments  1  minute  steps 
Switched Time adjustments

Operating periods per day - 3 per day(Separate 
programmes possible for each day of the week) 
10 minute steps

Override  1  hour  boost,  1  hour  extension  to  On 
period, instant advance

Mounting Industry standard 6 terminal plug in wall 
plate

Transmitter Frequency 868MHz

Design Standard EN60730-2-7 

IP30

EN300-220 R & TTE Directive

EN301-489 

Thermostat specification
HRT4-ZW

Power supply 2 x AAA alkaline batteries

Temperature ac/- 0.5°C

Transmitter frequency 868MHz

Dimensions 86mm x 86mm x36.25mm

Pollution control Degree2

Design standard EN60730 - 2-9

Temperature range 5°C – 30°C

Enclosure protection IP30

Operating temperature range 0-40°C

Case material Thermoplastic, flame retardant

For further replacement timeswitch exchange

information, please see the ‘Programmer

Wiring and Replacement Guide’ at

www.horstmann.co.uk

Use the categories shown under

CentaurPlus C11 and C17.

12

Secure Controls (UK) Limited

South Bristol Business Park

Roman Farm Road, Bristol, BS4 1UP

E-mail: [email protected]

Web Site: www.horstmann.co.uk

Leaflet number P84372 – Issue 3 

Summary of Contents for CentaurPlus ZW













Reviews: