background image

Press and hold 'BOOST' and 'ENTER' buttons to 'SIGN ON or 'PAIR' the HRT4-ZW thermostat.

Stage 1A - only used if ‘L’ is displayed instead of ‘I’

1) Turn the dial of the HRT4-ZW until the letter P appears in the display.

2) Press the dial twice and PP should appear in the display.

3)  Turn  the  dial  until  the  letter  ‘I’  appears  in  the  display  and  return  to  the  main 
instruction.

Under normal circumstances the HRT4-ZW thermostat and CentaurPlus C17 ZW will 
be  ‘paired’  easily  by  following  the  procedure  shown  under  Stage  1  of  the  pairing 
instructions.

Only use Stage 2 if a radio link cannot be successfully established between the two 
devices.

Stage  2  -  only  used  if  above  procedure  does  not  establish  a  successful 
communication link

1) Turn the dial of the HRT4-ZW until the letter P appears in the display.

2) Press the dial twice and PP should appear in the display.

3) Now turn the dial until letter E appears in the display.

4) Press the dial once and the display should flash ‘E’.

5) Press and hold the ‘Boost’ and ‘Enter’ buttons on the CentaurPlus ZW.

6)  Turn  the  thermostat  dial  until  ‘I’  appears  in  the  display  and  return  to  the  main 
instruction.

9

Summary of Contents for CentaurPlus ZW













Reviews: