background image

GB-14

D

GB

F

NL

I

E

Assistance in the event of 
malfunction

 ?  Fault
 !  Cause
 •  Remedy

Possible faults and suggested solutions
 ? 

 

The 

 symbol is displayed.

 ! 

 If the 

 symbol appears next to a measured 

value, this means that the value is invalid.

 • 

  After the next time synchronization, the data are 

recorded again correctly and 

 disappears.

 ? 

 

When pressing the user keys, the display 
remains switched off. A beep can neverthe-
less be heard.

 ! 

  Energy-saving mode is active. Due to excessive 

use of the index, the average energy consump-
tion has been exceeded.

 • 

  Leave the index unused for an extended period, 

e.g. 24 hours. After this, the user interface will 
once again be available.

 ?  When pressing the user keys, the display 

remains switched off and no beep can be 
heard.

 ! 

 The index is defective.

 • 

 Contact the manufacturer.

 ? 

 

The 

symbol is displayed.

 ! 

  Low index battery. This symbol is only displayed 

when index battery power is low.

 • 

 Replace the index battery.

 ? 

 

Display light is off.

 ! 

 Low index battery voltage.

 • 

 Replace the index battery.

 ! 

 Display light is defective.

 • 

 Contact the manufacturer.

 

In the case of faults which are not described here, 
contact the manufacturer immediately.

Accessories

External antenna

Only the following antennas are approved as external 
antennas.
Elster Part Nos.: 

72910264, “Retrofit kit external antenna EI3 / 2.5m” 

composed of:  

– service cover -cpl. EA EI3 (32320088) 
– PT screw K40x16 (03017232) 
– GSM antenna L=2.5m (04271001)

72910265, “Retrofit kit external antenna EI3 / 5m” 

composed of:  

– service cover -cpl. EA EI3 (32320088) 
– PT screw K40x16 (03017232) 
– GSM antenna L=5m (04271002)

Spare parts

Only the following spare parts are approved:

Communication module

Use only original Elster communication modules. 
Elster Part No.: 

72910267, “spare parts kit communication mod-

ule EI3” composed of:  

– communication module GSM EI3 (32320046)
– PT screw K40x16 (03017232) 
– screw locking cap EI (32447510)

Battery for the communication module

Use only original Elster batteries. 
Elster Part No.: 

72910266, “spare parts kit batterypack C.M. GSM 

EI3” composed of: 

– batterypack comm.module GSM EI3 (32447571) 
– PT screw K40x16 (03017232) 
– screw locking cap EI (32447510)

Screw locking cap

Part No.: 32447510.

Technical data

RoHS compliant

Application with diaphragm gas meters BK..B

Enclosure: IP 65.
Maximum allowable operating pressure p

max

 (as 

overpressure): see index plate, 
base gas pressure p

b

: see index plate, 

operating pressure range (absolute) p

g

800 to 1600 mbar.
Life of battery for index: approx. 15 years.
Life of battery for communication module:  
approx. 5 years.

Ambient temperature of index: -25 to +55°C (for 

entire meter, see index plate).

Accuracy of the clock: 0.4 s/day at 20°C on the 

day of manufacture.

Temperature measurement accuracy on the day of 

manufacture:  

  ± 0.2°C in the range from -10 to +55°C. 
  ± 0.25°C in the range from -25 to -10°C.
Pressure measurement accuracy: ± 5 mbar on the 
day of manufacture.

Summary of Contents for themis plus EI3

















Reviews: