manualshive.com logo in svg

Honeywell SS4-AI, Installation Manual And Operating Manual

Share
Download
Honeywell SS4-AI Installation Manual And Operating Manual Download Page 9

 

OPERATOR MANUAL // SECTION 2:  INSTALLATION 

 

HONEYWELL 

8 

SECTION 2:  INSTALLATION     

2.1 

Installation Procedure 

This section describes the installation of the Model SS4-AI Detector for the 
Stand-Alone mode.  It is recommended that junction boxes be used to wire 
the Model SS4-AI Detectors.  Determine a mounting location for the 
detector which is within the detectors range (see Detection Range and 
Field-of-View) and has a clear view of the fire threat area.  Where multiple 
detectors are used to cover a large area, the detectors should be located to 
allow overlapping Field-of-Views.  Determine the configuration settings for 
the device and the number of connections to be used. (Fire, Fire Verify, 
Fault, and Power)  The configuration settings and number of connections 
will depend on the Detection Range desired and the type of Fire Control 
Panel used.  For Configuration information see the Dip Switching Setting 
chart and the manual for your Fire Control Panel. 

2.1.1 

Installation Precautions 

The following precautions should be observed during installation of Model 
SS4-AI Detectors. 

1. 

Double-check to make sure that the external electrical power is 
turned 

OFF

 before connecting to the Model SS4-AI Detector

. 

2.  Do not handle the Model SS4-AI Detector's module (with its 

printed circuit boards) without being adequately grounded.  

Printed circuit board components are susceptible to damage from 
electrostatic discharge. Grounding may be accomplished by 
wearing an anti-static wrist strap connected to an earth ground. 

2.1.2 

Conduit Installation 

Model SS4-AI Detectors should be located to cover the specific "fire threat" 
areas. 

When planning the conduit, observe the following recommendations. 

1. 

If only one of the two ½ inch NPT conduit openings on the Model 
SS4-AI Detector enclosure is used, seal the unused opening with a 
threaded plug. 

2. 

In areas where moisture may accumulate, install an approved 
conduit trap or drain. 

3. 

A seal shall be installed within 6 inches of the enclosure for 
applications requiring a Class I, Div. 1 Explosion-Proof rating. 

Summary of Contents for SS4-AI
























Reviews:

No comments

Brands by name

Popular brands

Load more brands