Honeywell RS-232 Reference Manual Download Page 45

Page: 45 / 152

Function Parameter Index Reference

8/99

RS232 Communications Reference Manual

5. Function Parameter Index Reference

5.1 Parameter Index Numbers

Function Block parameter tables

Refer to the tables listed below to find the correct Dynamic (I/O) or Static (Configuration) parameter index
number for a given function block that is to be accessed through a communications message.

Abbreviations

The abbreviations used in the tables are:

REAL

Floating Point Analog Numbers

BOOL

Digital ON and OFF states

Contained Parameter

Input Value

Output Value

Read Only

R/W

Read/Write

Write

In this section

Refer to Table 4-1 for a listing of each function block type and respective reference page.

Table 5-1 Function Block Look-up Table

Function Block Type Identification Label

See Subsection

ABS

(Absolute Value)

5.2

ADD

(Addition 2 Inputs)

5.3

4ADD (Addition 4 Inputs)

5.4

(Analog Input)

5.5

ALM

(Analog Alarm)

5.6

2AND (AND - 2 Inputs)

5.7

4AND (AND - 4 Inputs)

5.8

8AND (AND - 8 Inputs)

5.9

AMB

(Auto/Manual Bias)

5.10

(Analog Output)

5.11

ASYS

(Alarm System Monitor)

5.12

BCD

(Binary Coded Decimal Translator)

5.13

BOOL (Free Form Logic)

5.14

CARB (Carbon Potential)

5.15

CMPR (Comparison)

5.16

DCMP (Deviation Compare)

5.17

Summary of Contents for RS-232

























































































































































Search results

Summary of Contents for RS-232

Reviews:

Honeywell RS-232, Reference Manual, Page: 45 / 152

Search results

Summary of Contents for RS-232

Reviews: