manualshive.com logo in svg

Honeywell ms2420, User Manual, Page: 4 / 88

Share
Download
Honeywell ms2420 User Manual Download Page 4

 

 

iv 

 

Startup ..........................................................................................................................................................42

 

Power-Up Test Mode....................................................................................................................................42

 

Configuration Mode.......................................................................................................................................42

 

Scale Operation

 

Scale Zeroing................................................................................................................................................43

 

Calibration.....................................................................................................................................................44

 

Tools Required........................................................................................................................................44

 

Scale Calibration Methods ......................................................................................................................44

 

Priming the Scale for Calibration (lbs. & kg) ...........................................................................................45

 

Scale Calibration Procedure (lbs. & kg) with Remote Display ................................................................46

 

Bar Code Calibration Procedure without Remote Display ......................................................................50

 

Calibration Verification..................................................................................................................................54

 

U.S. Pounds (lbs.)...................................................................................................................................54

 

Kilograms (kg).........................................................................................................................................55

 

Security Seal Installation...............................................................................................................................56

 

Pressure Sensitive Security Seal............................................................................................................56

 

Wire Security Seal (Conversion Kit 46-00239) .......................................................................................57

 

Maintenance

 

Horizontal Scan Window Replacement.........................................................................................................59

 

Daily Maintenance ........................................................................................................................................60

 

Troubleshooting

 

Troubleshooting Symptom / Solution Chart ..................................................................................................61

 

Scanner and Cable Terminations

 

Scanner Pinout Connections ........................................................................................................................65

 

Scanner Scale Pinout Connections ..............................................................................................................66

 

Cable Connector Configurations...................................................................................................................67

 

Regulatory Compliance

 

Safety............................................................................................................................................................69

 

EMC..............................................................................................................................................................70

 

Weights & Measures.....................................................................................................................................71

 

Limited Warranty ..............................................................................................................................................73

 

Patents...............................................................................................................................................................75

 

Index ..................................................................................................................................................................77

 

Customer Support ............................................................................................................................................79

 

Technical Assistance ....................................................................................................................................79

 

Product Service and Repair..........................................................................................................................80

 

Summary of Contents for ms2420

























































































Reviews:

No comments