manualshive.com logo in svg

Honeywell ms2420, User Manual, Page: 83 / 88

Share
Download
Honeywell ms2420 User Manual Download Page 83

 

 

79

Customer Support  

Technical Assistance  

If you need assistance installing or troubleshooting your device, please call your distributor or the nearest 
technical support office: 

North America/Canada 

Telephone:  (800) 782-4263 

E-mail:  [email protected] 

Latin America 

Telephone:  (803) 835-8000 
Telephone:  (800) 782-4263 

E-mail:  [email protected] 

Brazil 

Telephone: +55 (21) 3535-9100 
Fax:  +55 (21) 3535-9105 

E-mail:  [email protected] 

Mexico 

Telephone:  (803) 835-8000 

E-mail:  [email protected] 

Europe, Middle East, and Africa 

Telephone:  +31 (0) 40 7999 393 
Fax:  +31 (0) 40 2425 672 

E-mail:  [email protected] 

Hong Kong 

Telephone:  +852-29536436 
Fax:  +851-2511-3557 

E-mail:  [email protected] 

Singapore 

Telephone:  +65-6842-7155 
Fax:  +65-6842-7166 

E-mail:  [email protected] 

China 

Telephone:  +86 800 828 2803 
Fax:  +86-512-6762-2560 

E-mail:  [email protected] 

Japan 

Telephone:  +81-3-3839-8511 
Fax:  +81-3-3839-8519 

E-mail:  [email protected] 

Online Technical Assistance 

You can also access technical assistance online at www.honeywellaidc.com. 

 

Summary of Contents for ms2420

























































































Reviews:

No comments