Honeywell ms2420 User Manual Download Page 2 | Manualshive

Page: 2 / 88

Honeywell ms2420 User Manual Download Page 2

Disclaimer

Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information
contained in this document without prior notice, and the reader should in all cases consult HII to determine
whether any such changes have been made. The information in this publication does not represent a
commitment on the part of HII.

HII shall not be liable for technical or editorial errors or omissions contained herein: nor for incidental or
consequential damages resulting from the furnishing, performance, or use of this manual.

This document contains propriety information that is protected by copyright. All rights reserved. No part of this
document may be photocopied, reproduced, or translated into another language without the prior written
consent of HII.

© 2009 Honeywell International Inc. All rights reserved.

Web Address: www.honeywellaidc.com

Trademarks

Metrologic, MetroSelect, MetroSet

2

, Stratos

SCAN

, Stratos

SPHERE

, Stratos

SYNC

, Stratos

SCOPE

,

Stratos

SWAP

, and Stratos

SCHOOL

are trademarks or registered trademarks of Metrologic Instruments, Inc. or

Honeywell International Inc.

Microsoft, Windows, and Windows 95 are trademarks or registered trademarks of Microsoft Corporation.

IBM is a trademark of International Business Machines Corporation.

Other product names mentioned in this manual may be trademarks or registered trademarks of their respective
companies and are the property of their respective owners.

Patents

Please refer to page 75 for a list of patents.

«
1
2
3
4
...
»

Summary of Contents for ms2420

























































































Reviews:

No comments