manualshive.com logo in svg

Honeywell ms2420, User Manual, Page: 36 / 88

Share
Download
Honeywell ms2420 User Manual Download Page 36

 

Changing the Wake Area Sensitivity Level (Photocell LED Range Adjust)

 

 

The MS2400 Series bar code scanner wake area sensitivity level can be set to the end users preference by 
scanning one of the Photocell Sensitivity adjustment bar codes below. 

 

 
 

*Max Photocell  

Sensitivity

 

 
 

This feature enables the MS24xx to be at max 
sensitivity or far sensing for the wake up photo 
transistor.  

 

* This is the default setting. 

³ 2 2 1 2 0 0

 

 
 
 
 
 

Medium Photocell 

Sensitivity

 

 

 

This feature enables the MS24xx to be at a 
medium 1 sensitivity or medium sensing for 
the wake up photo transistor. 

³ 2 2 1 2 1 0

 

 
 

Low Photocell  

Sensitivity

 

 
 

³ 2 2 1 2 2 0

 

This feature enables the MS24xx to be at a 
low sensitivity or low sensing for the wake up 
photo transistor. 

 
 
 

Min Photocell 

Sensitivity

 

 
 

³ 2 2 1 2 3 0

 

This feature enables the MS24xx to be at the 
lowest sensitivity (close only) for the wake up 
photo transistor.   

 
 

*

  MS2400 Series Bar Code Scanner Default Setting 

 32 

Summary of Contents for ms2420

























































































Reviews:

No comments