4
5
ENGLISH GB
ENGLISH GB
Proceed as follows:
Once the wall mounting screws are correctly positioned and securely mounted
onto the wall using the supplied fixings (as per Operating Instructions) offer
up the rear panel of the heater to the screw heads, ensure that they are firstly
aligned with the opening of the ‘larger’ slots, then push the heater back
introducing the screws into these larger openings (Step 1) now gently move the
heater sideways left so that the heads of the screws are repositioned within the
smaller slots (Step 2). With the screws now positioned in the smaller slots, pull
down on the heater so that the screws are fully locked into position and the
heater is securely attached to the wall (Step 3), DO NOT operate the heater until
you are sure that it is fully secured.
OPERATING INSTRUCTIONS
(See page 2)
• Toggle both power setting switches to the OFF position.
• Plug the heater power cable into an outlet.
• Toggle the power setting switches to the desired power setting (fig. 1):
= Low – 800W
= Medium – 1000W
+ = High – 1800W
• Turn the thermostat knob clockwise ( ) to the highest temperature setting for
rapid warming.
• When the room reaches a comfortable temperature, turn the thermostat knob
counterclockwise ( ) until the heater switches off (a click is heard and the pilot
lights turn off). At this setting the thermostat will automatically turn the heater
on (the pilot lights illuminate) and off (the pilot lights go out) to maintain the
selected temperature.
• To turn the heater off, toggle the power setting switches to the OFF position and
unplug the heater.
AUTOMATIC ANTI-FROST FUNCTION
The heater is equipped with an automatic anti-frost function. Plug in the heater.
Toggle the power setting switches to any of the active settings ( , or + ). Turn
the thermostat knob counterclockwise to its lowest setting, indicated by the
snowflake icon ( ). As soon as the room temperature is below + 5 °C the heater
will automatically switch on. As the heater will automatically turn on in anti-frost
mode, make sure the heater is not covered or obstructed by any object.
AUTOMATIC SAFETY CUT-OUT
This heater is equipped with an automatic safety cut-out. If the heater stops
unexpectedly, the safety cut-out may have operated. Once the safety cut-out
has operated, the heater will not restart until the heater has been turned off
and cooled down. In this situation, you must toggle the power setting switches
to the OFF position and unplug the heater. Allow the heater to cool, then follow
the "Operating Instructions".
TIP-OVER SWITCH
The heater is equipped with an automatic tip-over switch that will disable the
heater if it is accidentally tipped over.
IF THE HEATER FAILS TO OPERATE
• Check for and remove any obstructions.
• Check if the heater is in the standing position.
• Check if the heater is plugged in. Also check if the power socket is working
(e.g. plug in a different working electrical device).
• Make sure that the thermostat is not set too low. With the power setting
switches set to one of the active settings ( , or + ) turn the thermostat knob
clockwise until the heater turns on again (pilot lights illuminate).
• If the heater still does not work, consult the warranty for further instructions.
CLEANING
We recommend you to clean the appliance with a vacuum cleaner twice a year (or
before if you notice performance to be impaired).
1. Unplug the unit.
2. Allow it to cool down for 20 minutes.
3. Use a vacuum cleaner to suck out dust and dirt from both grilles.
MAINTENANCE
In the event of overheating, the safety system will automatically turn off the
heating elements and/or the motor. If this happens please remove any obstacles to
the air outlet grille and clean the unit as indicated under cleaning instructions.
DISPOSAL
This appliance complies with EU legislation 2012/19/EU on end of life
recycling. Products showing the ‘Crossed Through’ wheeled bin symbol on
either the rating label, gift box or instructions must be recycled separately
from household waste at the end of their useful life.
Please DO NOT dispose of appliance in normal household waste. Your
local appliance retailer may operate a ‘take-back’ scheme when you are
ready to purchase a replacement product, alternatively contact your local
government authority for further help and advice on where to take your
appliance for recycling.
CONDITION OF PURCHASE
As condition of purchase the purchaser assumes responsibility for the correct use
and care of this Kaz product according to these user instructions. The purchaser
or user must himself or herself decide when and for how long this Kaz product is
in use.
WARNING: IF PROBLEMS ARISE WITH THIS KAZ PRODUCT, PLEASE OBSERVE
THE INSTRUCTIONS IN THE GUARANTEE CONDITIONS. DO NOT ATTEMPT TO
OPEN OR REPAIR THE KAZ PRODUCT YOURSELF, AS THIS COULD LEAD TO
TERMINATION OF THE GUARANTEE AND CAUSE DAMAGE TO PERSONS AND
PROPERTY.
This product carries the CE mark and is manufactured in conformity with the
Electromagnetic Directive 2004/108/EC, the Low Voltage Directive 2006/95/EC and
the RoHS Directive 2011/65/EU.
Technical modifications reserved
HCE890BE
220-240V ~ 50Hz
1800W
IMPORTANT SAFETY INSTRUCTIONS
Read through all the instructions before starting
to use the appliance. Keep this manual in a safe
place for future reference.
These instructions are also available on our website.
Please visit www.hot-europe.com.
• This appliance must only be operated as
instructed in this user manual.
• This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge if they have been
given supervision or instruction concerning use of
the appliance in a safe way and understand the
hazards involved. Children shall not play with the
appliance.
• Children of less than 3 years should be kept away
unless continuously supervised.
• Children aged from 3 years and less than 8 years
shall only switch on/off the appliance provided
that it has been placed or installed in its intended
normal operating position and they have been
given supervision or instruction concerning use of
the appliance in a safe way and understand the
hazards involved. Children aged from 3 years and
less than 8 years shall not plug in, regulate and
clean the appliance or perform user maintenance.
•
DO NOT COVER WARNING: In order to avoid
overheating, do not cover the heater with
anything, as indicated by the symbol. This can
lead to overheating, fire or electric shocks. Ensure
that the air intake and outlet vents are not
obstructed.
• CAUTION: Some parts of this product can become
very hot and cause burns. Particular attention has
to be given where children and vulnerable people
are present.
• Do not use this heater in the immediate
surroundings of a bath, a shower or a swimming
pool.
• The appliance is intended only for use indoors,
not for outdoor use or commercial use.
• Do not use the appliance anywhere near easily
flammable gases or substances such as solvents,
lacquers, glues, etc. Some of the internal parts
can be hot and could throw sparks.
• Do not position the appliance immediately below
a power socket.
• Keep flammable materials at least 100cm away
from the heater. To prevent burns, do not allow
bare skin to come in contact with hot surfaces.
• If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
• Never touch the unit with wet hands.
• Check for any obstructions. If you find an
obstruction, turn off the heater using the power
button on the control panel. Allow the heater to
cool completely, then remove the obstruction.
Wait at least 10 minutes, then turn on the heater
and follow the instructions for use.
COMPONENTS
(See page 2)
1. Air inlet grille
2. Air outlet grille
3. Power setting switches with integrated pilot lights
4. Thermostat knob
5. Handle
6. Feet
7. Power
cord
8. Wall mounting brackets
9. Feet assembly screws
10. Wall mounting screws & rawl plugs (for concrete)
ASSEMBLY
(See page 3)
This heater may be used with feet on the floor or attached directly to the wall.
FOOTSTAND INSTALLATION
1. For floor use, attach the feet to the lower part of the heater and align the
feet with the screw holes (fig.2).
2. As shown in fig. 3, please tighten the feet at the bottom of the heater using
the feet assembly screws provided.
3. Place the heater on a firm, level, open surface at least 90cm away from any
other object. DO NOT use on an unstable surface such as bedding or deep
carpeting.
WALL MOUNTING INSTALLATION
1. For wall mounting, find a position for the heater ensuring proper clearances
(fig. 4).
2. Mark the positions of the 3 holes on the wall (fig. 4A).
3. Drill the holes with a drill bit (fig. 5). Insert the rawl plugs into the holes (fig. 6).
4. Screw the 3 screws into the rawl plugs into the wall (fig. 7).
5. Place the heater, let the screws fit in the wall mounting brackets on the back
of the heater (fig. 8).
For wall mount installation, please ensure that the wall mounting screws
are correctly inserted and positioned within the correct slots on the rear of the
heater (see Steps ‘1,2,3’ of Fig. 9).
This product is only suitable for
well-insulated spaces or occasional use.
