background image

12

OPERATION INSTRUCTIONS

CHECKING FOR LEAKS

gs on the LP gas tank valve, gas hose

and regulator for leaks with a water and soap solution.

 

  Always perform leak test prior to lighting the grill.

 

  Do not smoke while testing for a leak.

 

  Always perform leak tests outdoors in a well-ventilated area.

 

  Do not use the grill until any and all leaks are corrected.

 

  If you are unable to correct a leak, disconnect the propane supply and call a gas appliance service

    dealer.

PERFORM LEAK TEST

 

 

  Prepare leak test solution by 50/50 ratio of liquid dish soap and water.

    Total solution required is approximately 2 - 3 ounces (70 - 90 ml).

    Put leak test solution in a spray bottle.

 

  Ensure all control knobs are in the   OFF position.

 

  Connect the gas hose to the gas supply.

 

  Open the LP gas tank valve.

 

  Spray leak test solution on all gas carrying connections an

    of applied test solution indicates a gas leak.  If leaks are detected or you smell or hear gas, shut off the

    gas supply valve immediately and repair or replace the defective part. Do not use the grill until 

    all  leaks are corrected.

WARNING

ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE FOLLOWED TO 

PREVENT FIRE, DAMAGE AND/OR INJURY.

CAUTION

Only use the regulator and hose assembly provided!

  If a replacement is necessary, please call

our customer service center. Do not use replacement parts that are not intended for this grill.

Summary of Contents for G410























Reviews: