manualshive.com logo in svg

Honeywell G410, Operating Manual, Page: 20 / 22

Share
Download
Honeywell G410 Operating Manual Download Page 20

20

 

The electronic ignition requires 1 “AA” alkaline battery, which is included.

WARNING

DO NOT mix old and new batteries.

DO NOT mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel-Cadmium) batteries.

If you have any questions regarding the product, please call customer service at  213-4467172

PROBLEM  

POSSIBLE CAUSE 

CORRECTIVE ACTION

Low Heat.

Excessive
Flare Ups.

1. 

 

 The igniter electrode may be 

covered with grease or residue.

 

 

 

 

 

 

   

2. 

the unit

.

1.
 

2.

3.

1.

2.

3.

4.

 
 
 
 
 
 
 

1.

2.

3.

The igniter electrode may have 

a loose or disconnected wire.

Cracked or broken ignition elect-

rode .
Dead battery or faulty battery con-

nection.

3.

4.

Grease and/or residue build-up

on heat tents or in firebox

.

Excessive dripping of fat or m-

arinade from food

.

Cooking temperature too high

.

Clean the grill components

.

Trim the fat from meat and use non-oil

 based marinades.

Lower temperature accordingly.

Call a qualified service agency to check

the gas supply pressure and correct the 

pressure.

Clean the ignitor electrode

.

Check the connection and reconnect 

any loose or disconnected wires.
Replace ignition electrode (see Replace

ment parts list)

.

Perform any of the following: 

a.Replace battery

b.Check to see if battery is inserted

correctly.

c.Check for any corrosion around ba-

ttery terminals.

d.Check wire connections as stated a-

bove 

The burner does not 

light  by using the ig-

 

   

 

nitor procedure (we-

ak or no sparkbeing

generated).

CARE AND MAINTENANCE

TROUBLESHOOTING

Summary of Contents for G410























Reviews:

No comments