Honeywell FF-SRS5988 Instructions For Use Manual Download Page 5 | Manualshive

Page: 5 / 13

Honeywell FF-SRS5988 Instructions For Use Manual Download Page 5

107018-04 EN FR26 GLO 1198 Printed in Germany

5

EXTENSION MODULES AND EXTERNAL
CONTACTORS

One or more FF-SRE3081 Extension Modules or

external contactors with positively driven contacts
can be used to multiply the number of contacts of the
FF-SRS5988 Emergency Stop Module. If multiple
safety contacts are used in parallel with one load,
the maximum allowed current can be increased.

For connection of the FF-SRE 3081 to the FF-SRS

5988 module, see the Installation Instructions for the
FF-SRE 3081 Extension Module.

CONTACT MULTIPLICATION VIA EXTERNAL
RELAYS

•

If contact multiplication via external safety relays

(or the FF-SRE3081 Extension module) is
necessary, connect one normally closed contact
of each relay (or 81/82 of the Extension module)
in series into the Final Switching device
monitoring loop (terminals Y1/Y2).

Failure to comply with this instruction could
result in death or serious injury.

LED INDICATORS

The FF-SRS5988 module has three green LED

status indicators (Power, K2 and K3) as illustrated
below.

The Power LED indicates power is applied to the

safety control module. Illuminated K2 and/or K3
LED’s indicate(s) that the corresponding internal
safety relay is energized. Both K2 and K3 relays
must be energized to have the normally open
contacts 13/14...63/64 in a closed position. If one of
the safety relays de-energizes, the normally closed
contact will close.

FIG 8. MODULE FRONT PANEL

K2

K

23

K3

13

A1

S

12

S

21

S

23

S

22

S

12

13 23 33

53

43

63 81

A4

(-)

S

33

S33

S12

S

34

S34

S12

Y1

Y1

Y2

Y2
X1
X2

S21
S22
S23

X1 X2

A1

14

14

PE(-)

24

24

53

34

34

63

44

44

43

54

54

33

64

64

23

82

82

A2

A2

81

PE

(-)

S11/A3+

S11

A3
(+)

FIG 9. FUNCTIONAL DIAGRAM

Start push-
button

Emergency
stop

K2

K3

Input

Output

released

activated

released

activated

*

* Line fault Detection on Start push-button:
If the start push button is closed before voltage is
applied to S12 and S23 the safety contacts of the
module cannot close.
This additional feature ensures the detection of a line
fault via the start push-button or a blocked start push
button. In case of a push-button failure the module
can not be restarted.
In order to let the line fault detection work properly,
the internal safety relays should have been de-
energised for at least 10 seconds before.

«
...
3
4
5
6
7
...
»

Summary of Contents for FF-SRS5988














Reviews:

No comments