manualshive.com logo in svg

Honeywell FF-SRS5988, Instructions For Use Manual, Page: 11 / 13

Share
Download
Honeywell FF-SRS5988 Instructions For Use Manual Download Page 11

 

107018-04 EN FR26 GLO 1198 Printed in Germany

 11

FIG. 14.  FF-SRS5988 TROUBLESHOOTING FLOW DIAGRAM (PAGE 2 OF 3)

Yes

No

Manual start mode used

with an external start push

button?

Ensure jumper is NOT set

between X1/X2.  Push and

release the external start push

button between S33/S34.

Yes

No

Yes

Check for proper

machine operation

Damaged

contacts.

Ensure maximum

load is within

specification.

Replace module.

Ensure the FSD monitoring loop (Y1/Y2) is closed

when the external start push button is activated and

opened when the pushbutton is released

(this tests the correct operation of the push button or

optional external relays/contactors)

Is the

problem

resolved?

Are the K2 and K3

LEDs ON?

Are the

outputs contacts

13/14...63/64

closed and is 81/82

opened?

From

Fig. 15

Yes

No

No

Go to

Fig. 15

From

Fig. 13

Ensure jumper is set

between X1 and X2.

Ensure that Y1 and Y2

are closed  (possible

failure of optional external

safety relays).

The problem

exists

external to

the module.

Check for

external
causes.

(wiring, etc.)

Summary of Contents for FF-SRS5988














Reviews:

No comments