Honeywell F-BO-AFE70 Series Installation, Connection, Commissioning, Maintenance Download Page 43

Page: 43 / 48

User Manual Series F-BO-AFE70

Chapter 12 • Specifications

Specifications

The specifications that are stated in the sections that follow are – with the exception of the values
that are given as maximum or minimum values – typical values which are subject to manufactur-
ing tolerances.

Housing

Installation

wall installation, surface type

Material

sheet steel, powder coated (cover)
sheet steel, galvanised (bottom plate)
aluminium, anodized (valve block)

Colour

grey white, RAL 9002 (cover)

Protection class

IP10 (condition on delivery)
IP20D (expertly installed)
IP54 (control electronics)

Dimensions W × H × D (excl. push-in fittings)

204 × 68 × 160 (mm)

Dimensions W × H × D (incl. push-in fittings)

204 × approx. 201 × 160 (mm)

Weight

approx. 3.2kg

Ambient temperature F-BO-AFE70-2

+5°C to +50°C

Ambient temperature F-BO-AFE70-3

-20°C to +40°C

Relative humidity

max. 95% at 40°C, (no condensation)

Accuracy of the timer

b5°C and +50°C

11 minutes per year

between -20°C and +5°C

45 minutes per year

Supply voltage

Normal operation

21.6 ... 30.0VDC

Solenoid valve continuously energised

21.6 ... 26.4VDC

Current consumption at 24V

F-BO-AFE70-2

8mA (normal condition, solenoid valve
de-energised)
300mA (solenoid valve energised)

F-BO-AFE70-3

8mA (normal condition, solenoid valve
de-energised)
370mA (solenoid valve energised)

Minimum output current of the power unit

1.5A

Connection type

pluggable screw terminals, 2-pin

Wire gauge

max. 2.5mm² (single-wire)

Fault input (terminals 3, 4)

Minimum activation time

1sec

Line resistance

max. 50Ω per core

End-of-line resistor

EOL

AFE 5.6kΩ

Short circuit | interruption

< 200Ω | > 7.5kΩ

Input 'Manual activation' (terminals 11, 12)

Minimum activation time

125ms

Line resistance

max. 50Ω per core

Output 'Slave activation' (terminals 5, 6)

Contact type

semiconductor switch, normally open contact,
potential-free

Switching power

max. 30V (internal protective resistor 6.8kΩ)

Fault output (terminals 7, 8)

Contact type

semiconductor switch, normally closed contact,
potential-free

Switching power

max. 30V/ max. 120mA

Compressed-air characteristics F-BO-AFE70-2 (ANR means: at 0.1MPa (1bar), 20°C, 65% relative humid-

ity)

I56-4252-010
D200-104-00

Summary of Contents for F-BO-AFE70 Series

















































Search results

Summary of Contents for F-BO-AFE70 Series

Reviews:

Related manuals for F-BO-AFE70 Series

Brands by name

Popular brands

Honeywell F-BO-AFE70 Series, Installation, Connection, Commissioning, Maintenance

Search results

Summary of Contents for F-BO-AFE70 Series

Reviews:

Related manuals for F-BO-AFE70 Series

Brands by name

Popular brands