Honeywell F-BO-AFE70 Series Installation, Connection, Commissioning, Maintenance Download Page 35 | Manualshive

Page: 35 / 48

background image

User Manual Series F-BO-AFE70

Chapter 9 • Connection and parameterisation

Fig. 13:

Connection of two Automatic Purging Units F-BO-AFE70 in the master-slave mode.
A … Aspirating smoke detector (in order to provide a clearer overview, only the connections that

are absolutely necessary for the Purging unit are shown)
The two relay contacts are shown in the state where no voltage is being provided to the
relays.

B … Power unit for the aspirating smoke detector (observe the country-specific regulations

regarding the power supply of aspirating smoke detectors and special detectors)

C … Fire alarm message to the fire detection control panel (observe the connection conditions

for the fire detection control panel used)

D … Fault message to the fire detection control panel (observe the connection conditions for the

fire detection control panel used)

E … Actuation output on the fire detection control panel (observe the connection conditions for

the fire detection control panel used)
This output is used to start the Purging processes if the ASD experiences a fault.
Manual Purging activations can be carried out by manipulating operating devices that are
intended for this purpose, provided that this feature has been prepared by the installer of the
system.

F … In addition, the fault outputs of the F-BO-AFE70 can optionally be connected to the fire

detection control panel in order to transmit the fault of the F-BO-AFE itself (through wire
breakage of this fault detector line).

The aspirating smoke detector, the master unit as well as all slave units can be powered by differ-
ent power supplies or by the same power supply.

If several Purging units, each with its own independent power supply device, are operated with a
common timer for synchronising the time or with a common push-button „Manual activation“ or
something similar, the supply voltage minus terminals of the Purging units (terminal 2) must be
connected to each other.

I56-4252-010
D200-104-00

35

«
...
33
34
35
36
37
...
»

Summary of Contents for F-BO-AFE70 Series

















































Reviews:

No comments

Related manuals for F-BO-AFE70 Series

Brand: MacDon Pages: 84

Brand: MacDon Pages: 89

Brand: Patton electronics Pages: 18

Brand: NEILPRYDE Pages: 55

Brand: HANYOUNGNUX Pages: 4

Brand: Park House Healthcare Pages: 6

Brand: J&M Pages: 33

Brand: Olympus Pages: 56

Brand: P-Q Controls Pages: 5

Brand: P+L Systems Pages: 2

Brand: B. Braun Pages: 40

Brand: B. Braun Pages: 4

Brand: Zodiac Pages: 32

SpinVessel VP 418SV3-1-850RB-CC

Brand: V&P Scientific Pages: 9

MACDON C HARVESTEC 6000

Brand: CORN Pages: 24

Brand: Star Pages: 16

Brand: Vision & Control Pages: 32

Balance & Pilates

Brand: Lanaform Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands