Honeywell Dolphin Power Tools User Manual Download Page 50

Page: 50 / 176

2 - 34

Scanning Bar Codes Directly from the Power Tools Main Window

When the Power Tools or Demos main windows are open, press the SCAN key and:

• If there is only one bar code in the package, EZConfig Client decodes and deploys the bar code without

opening the EZConfig Client window.

• If there are multiple bar codes in the package, EZConfig Client decodes the first bar code and opens

the EZConfig Client window showing that one bar code in the package has been scanned.

Launching EZConfig Client with a HotKey

Pressing ALT + SCAN launches EZConfig Client from any application window after you activate the
HotKeys Power Tool; see

HotKeys

on page

6-5.

ScanWedge

Bar code decoding in EZConfig Client is compatible with ScanWedge. You can set ScanWedge to pass
bar code information to EZConfig Client for further processing. For details, see

Accept EZConfig

on page

5-4.

Command Line Arguments

/%filename

Executes the EXM file; this is the default entry.

Quiet mode

Full screen

No menu

Exit if first scan fails to deliver a valid bar code

Accept (decode) unsecure bar codes

Summary of Contents for Dolphin Power Tools

















































































































































































Search results

Summary of Contents for Dolphin Power Tools

Reviews:

Brands by name

Popular brands

Honeywell Dolphin Power Tools, User Manual

Search results

Summary of Contents for Dolphin Power Tools

Reviews:

Brands by name

Popular brands