manualshive.com logo in svg

Honeywell Dolphin Power Tools, User Manual

Share
Download
Honeywell Dolphin Power Tools User Manual Download Page 137

8 - 7

Restoring the Registry

Note: For the Dolphin 7600, see 

RegRestore

 on page 

8-12.

After you have backed up the registry, a _RegBackup.reg file of the entire registry is stored in the 

\IPSM\Autoinstall

 (

\Honeywell 

for 6100/6500) folder.

You have a number of options to restore the registry by loading the _RegBackup.reg file.

RegRestore

On the 

Dolphin Power Tools Main Window

 (see page 1-2), tap the 

RegRestore

 icon 

. 

Tap on the REG File 

Tapping on a REG file in any folder immediately tries to add the information in that file to the registry. A 
message appears asking if you want to add the information to the registry. Tap 

Yes

 to add the information. 

Cold Boot

Because this REG file is stored in the 

\IPSM\Autoinstall

 (

\Honeywell 

for 6100/6500) folder, 

Autoinstall will launch and install this REG file during the next cold boot.

Summary of Contents for Dolphin Power Tools

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands