Honeywell Dolphin Power Tools User Manual Download Page 123

Page: 123 / 176

6 - 19

DLL VERSION INFO:

Decoder.dll

1.15

Current Decoder.dll API build revision.

waDecodeCE.dll

2.16

Current waDecodeCE.dll API build revision.

Matrix Engine

1.97.1.2

Current Matrix engine build revision.

HHPScanInterface.dll

1.15

Current HHPScanInterface.dll API build revision.

Scan Driver

1.100

Current scan driver build revision.

HHPICMediaHW.dll

1.00.01

Current HHPICMediaHW.dll API build revision.

ImgCE.dll

2.04.05

Current ImgCE.dll API build revision.

DibCE.dll

2.04.00

Current DibCE.dll API build revision.

SYSTEM PARAMETERS:

BatteryIdleTimeout

ExternalIdleTimeout

OEMInfo

HHP, Hand Held
Products, or
Honeywell

Name of the OEM.

PlatformType

PocketPC

Type of platform (CE or PPC)

NETWORK INFO:

Hostname

test

The logical name assigned to the terminal.

NumberOfAdapters

Number of network adapters installing in the terminal.

1: Mac Address

000B6C1B8CC5

Terminal’s MAC and IP addresses.

1: IP Address

0.0.0.0

2: Mac Address

8200600FE800

2: IP Address

169.254.2.1

RADIO INFO:

Current Mode:

Wi-Fi and Bluetooth

Radio or radio combination currently enabled.

Modes Supported (1–X):

Bluetooth
Wi-Fi
Wi-Fi and Bluetooth
GSM
GSM and Bluetooth

Radios and radio combinations the terminals supports.
Each radio and radio combination is its own supported
mode.

[Radio] Hardware:
[Radio] Hardware:
[Radio] Hardware:

No WiFi Hardware
Radio Driver’s
Name

The radio hardware installed.

Sample SysInfo Text

Field

Sample Data

This entry specifies the …

Summary of Contents for Dolphin Power Tools

















































































































































































Search results

Summary of Contents for Dolphin Power Tools

Reviews:

Honeywell Dolphin Power Tools, User Manual, Page: 123 / 176

Search results

Summary of Contents for Dolphin Power Tools

Reviews: