background image

Copyright, Notices, Trademarks

This work contains valuable, confidential and proprietary information. Disclosure, use or reproduction outside of BW Technologies by Honeywell (BW Technologies) and/or Honeywell 
International Inc. (Honeywell) is prohibited except as authorized in writing. This unpublished work is protected by the laws of the United States and other countries.
While this information is presented in good faith and believed to be accurate, BW Technologies and/or Honeywell disclaims the implied warranties of merchantability and fitness for a particular 
purpose and makes no express warranties except as may be stated in its written agreement with and for its customers.
In no event is BW Technologies by Honeywell and/or Honeywell liable to anyone for any indirect, special or consequential damages. The information and specifications in this document are 
subject to change without notice. The Sampler is a trademark(s) of Honeywell International, Inc. Other brand or product names are trademarks of their respective owners.

Signal Words

This document uses the following signal words, as defined by ANSI Z535.4-1998:

International Symbols

n

Approved to both U.S. and Canadian Standards by CSA International

g

European Explosives Protection

Hazardous situation which, if not avoided, 

will 

result in death or serious injury. This symbol identifies the most extreme hazardous situations.

Hazardous situation which, if not avoided, 

could

 result in death or serious injury.

Hazardous situation which, if not avoided, 

may

 result in moderate or minor injury.

Situations which, if not avoided, may result in property damage.

Summary of Contents for D4-PF-1





















Reviews: