manualshive.com logo in svg

Honeywell APT4000PH, User Manual

Share
Download
Honeywell APT4000PH User Manual Download Page 45

88

APT4000PH

Calibration error messages

Asymmetry potential out of range (±60 mV)

• Electrode worn out
• Buffer solution contaminated
• Buffer does not belong to configured buffer set
• Temperature probe not immersed in buffer 

solution (for automatic temperature compensation)

• Wrong buffer temperature selected

(for manual temperature specification)

• Nominal electrode zero point 

≠

pH 7

Symbol flashes:

Problem 
Possible causes

Problems during recognition 
of the buffer solution

• Same or similar buffer solution was used 

for both calibration steps

• Buffer solution used does not belong to 

buffer set currently configured in the analyzer

Electrode slope out of range 
(80-103 %)

• Electrode worn out
• Buffer solution contaminated
• Buffer does not belong to configured 

buffer set

• Temperature probe not immersed in 

buffer solution (for automatic 
temperature compensation)

• Wrong buffer temperature set (for manual 

temperature specification)

• Electrode used has different nominal slope

89

Problems during recognition 
of the buffer solution (continued)

• During manual calibration the buffer solutions 

were not used in the specified order

• Buffer solutions contaminated
• Wrong buffer temperature set 

(for manual temperature specification)

• Electrode defective
• Electrode not connected
• Electrode cable defective

Symbol flashes:

Problem 
Possible causes

Calibration was canceled after approx.
2 min, because the electrode drift was too
large.

• Electrode defective
• Electrode dirty
• No electrolyte in the electrode
• Electrode cable insufficiently shielded or defective
• Strong electric fields influence the measurement
• Major temperature fluctuation of the buffer solution
• No buffer solution or extremely diluted

Summary of Contents for APT4000PH




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands