manualshive.com logo in svg

Honeywell APT4000PH, User Manual

Share
Download
Honeywell APT4000PH User Manual Download Page 26

50

APT4000PH

Configuration

Alarm settings

Select Sensocheck 

Delay

LED in Hold mode

Code Display

Menu group

Select menu item

Alarm
settings

AL.

End:

Press 

CONF

, then 

ENTER

15

16

Alarm

Alarm contact

The alarm contact is closed during normal operation
(N/C). It opens in the case of alarm or power outage. 
As a result, a failure message is provided even in the
case of line breakage (fail-safe behavior). For contact rat-
ings, see Specifications.

Error messages can also be signaled by a 22 mA output
current (see Pg 39, 

The operating behavior of the alarm contact is shown on
Pg 90.

The 

alarm delay

acts on the LED, the 22 mA signal

and the alarm contact.

45, 86).

51

Code Display

Action

Choices

ON / 

OFF

AL.

Select Sensocheck
(continuous monitoring of glass and
reference electrode – not available
with DURAFET II pH electrode)
Select with 

key, 

proceed with 

ENTER

Alarm delay
Select with 

key, edit number with

key, proceed with 

ENTER

0010 SEC

(0000 to
0600 SEC)

LED in Hold mode
Select with 

key, edit number with

key, proceed with 

ENTER

ON / 

OFF

Parameter setting

Alarm

Hold

ON

on

flashes

OFF

flashes

off

LED state:

Summary of Contents for APT4000PH




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands