manualshive.com logo in svg

Honeywell ADEMCO Vista-12C, Installation And Setup Manual

Share
Download
Honeywell ADEMCO Vista-12C Installation And Setup Manual Download Page 97

 

 

7-1 

S E C T I O N   7  

Testing the System 

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

 

About Test Procedures

 

After the installation is complete, you should perform the following tests: 
System Test: .................Checks that all zones have been installed properly. 
Dialer Test:...................Checks that the phone connection to the central station is working 

properly. 

Go/No Go Test: .............Checks that transmissions can be received from transmitters. Should 

be performed before permanently mounting transmitters. 

Sensor Sniffer Mode:....Allows one-man walk test of entire system. 
Battery Tests:...............Automatic battery tests are performed by the system. See Automatic 

Battery Test paragraph for details. 

 

System Test 

With the system in the disarmed state, check that all zones are intact (not faulted). Doors 
and windows with contacts should be closed, PIRs should be covered (use a cloth to mask 
them temporarily if necessary). If a “NOT READY” message is displayed, press [

∗

] to display 

the faulted zone(s). Restore faulted zone(s) if necessary, so that the “READY” message is 
displayed. 
1.  Enter Installer Code + 5 [TEST] , then press “0” at the prompt to start Walk Test mode. 

1=DIAL, 0=WALK 

(no special display on Fixed-Word keypads) 

 

The following will be displayed: 

TEST IN PROGRESS 

(“dd” displayed on Fixed-Word Display Keypads) 

 

A Contact ID report will also be sent (code 607) 

2.  Upon entering the system test mode, the outside sounder should sound for 1 second. 

If the backup battery is discharged or missing, the sounder may not turn on and a “LOW 
BATTERY” report will be transmitted with a “TEST” report.  
The keypad will beep once per minute as a reminder that the system is in the Test mode.  

NOTE:

  Wireless motion detectors (Passive Infrared units) will send signals out only if 

they have been inactive for 3 minutes from their prior transmission (conserves battery 
life).  

3.  Test all sensors using the procedure described in the User’s Guide “Testing the System” 

section. 

4.

 

After checking sensors, turn off the test mode by entering installer code + OFF. 

 

NOTE

: Test mode automatically ends after 4 hours. During the final 5 minutes (after 3 

Summary of Contents for ADEMCO Vista-12C

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands