manualshive.com logo in svg

Honeywell ADEMCO Vista-12C, Installation And Setup Manual

Share
Download
Honeywell ADEMCO Vista-12C Installation And Setup Manual Download Page 15

Mounting and Wiring the Control

 

 

2-7 

 

Basic Wired Zones 

Normally Open Zones/Normally Open EOLR Zones  

1.  Connect open circuit devices in parallel across the 

loop; for EOLR zones, connect the EOLR across the 
loop wires at the last device. 

2.  Enable normally open/EOLR zones using Zone 

Programming mode, “Hardwire Type” prompt. 

 

Normally Closed Zones/Normally Closed EOLR Zones  

1.  Connect closed circuit devices in series in the high (+) 

side of the loop; for EOLR zones, connect the EOLR in 
series following the last device. 

2.  Enable normally closed/EOLR zones using Zone 

Programming mode, “Hardwire Type” prompt.. 

 

Double-Balanced:

 

Connections as shown (resistors 

provided for one device in selected models); maximum of 
8 sensors on each double-balanced zone. 

 

IMPORTANT:

 Double-balanced zones provide unique 

tamper signalling on the same 2 wires used for alarm 
signalling, and should be used as burglary or emergency 
zones only. Do not use double-balanced zones as fire 
zones.  

 

Zone Doubling: 

Connections as shown (resistors 

provided).

 

 

2k

2k

2k

ZONE 3

2k

2k

2k

ZONE 4

12

13

14

z

one-002-V0

TAMPER

CONTACTS

TAMPER

CONTACTS

            

10

11

6.2k

ZONE 10

3k

ZONE 2

z

one-004-V0

 

 

Double Balanced Zones 

Zone Doubling 

Figure 5.  Configuring Zones

  

Notes 

•

 EOLR:

If the EOLR is not at the end of 

the loop, the zone is not properly 
supervised and the system may not 
respond to an “open” on the zone. 

•

  Zone 1 is intended only for EOLR 

usage. 

 

Zone Doubling: 

This feature provides two unique zone 
identifications for normally closed 
sensors connected to each basic wired 
zone (but does not increase the total 
number of zones supported by the 
control). Do not use zone doubling for 
fire zones. If enabled (Zone 
Programming mode, “Hardwire Type” 
prompt, option “3”), basic wired zones 
are automatically paired as follows: 

 

 

Zone 

Paired with zone 

 

2 10 

 3 

11 

 4 

12 

 5 

13 

 6 

14 

 

 
NOTE:

 A short across the EOL (i.e., at 

terminal) on either zone of a zone-
doubled pair or on a double-balanced 
zone causes a tamper condition 
(displayed at keypad as CHECK).  

 

 

 

 

Summary of Contents for ADEMCO Vista-12C

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands