manualshive.com logo in svg

Honeywell ADEMCO Vista-12C, Installation And Setup Manual

Share
Download
Honeywell ADEMCO Vista-12C Installation And Setup Manual Download Page 28

Installation and Setup Guide 

 

 

3-2 

Zones and Partitions  

Each protection zone needs to be programmed with various attributes using *56 Zone 

Programming mode or *58 Expert Programming mode. Refer to those sections for detailed 
procedures. 

The system can control three independent areas of protection (known as partitions) for use 

by independent users, if desired, by simply assigning zones to one of the partitions during 
zone programming. The system, by default, automatically distributes users among the three 
partitions. The master user can change the user number distributions.  

Zones can also be assigned to a common area partition if partition 3 is so designated, which 

is an area shared by users of the other two partitions (such as a lobby in a building). This 
allows either independent partition to arm, while leaving the common area partition 
disarmed for access into the other partition. The following describes the functioning of the 
common area partition, if used: 

•  The common area sounds and reports alarms only when both the other partitions are 

armed. If only one partition is armed, the system ignores faults in the common area. 

•  Either partition may arm its system if the common area is faulted, but once armed, the 

other partition will not be able to arm unless the common area zones are first bypassed or 
their faults are corrected. 

•  Faults in the common area are displayed on common area keypads, and will also appear 

on another partition’s keypad when that partition is armed. 

•  Either partition can clear and restore the common area after an alarm. 

Keypads 

Keypads are identified by predefined addresses (starting at address 16) as follows: 

Address Keypad 

Program 

Field 

 16   

keypad 

1 

•

 always enabled for partition 1,  

   

NOTE: First keypad is address 16.

 

  

 

 

all sounds enabled. 

 17   

keypad 

2 

•

 data field *190 

 18   

keypad 

3 

•

 data field *191 

 19   

keypad 

4 

•

 data field *192 

 20   

keypad 

5 

•

 data field *193 

 21   

keypad 

6 

•

 data field *194 

 22   

keypad 

7 

•

 data field *195 

 23   

keypad 

8 

•

 data field *196 

 

Summary of Contents for ADEMCO Vista-12C

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands