manualshive.com logo in svg

Honeywell ADEMCO Vista-12C, Installation And Setup Manual

Share
Download
Honeywell ADEMCO Vista-12C Installation And Setup Manual Download Page 25

Mounting and Wiring the Control

 

 

2-17 

On-Board Triggers 

 

Connect field wiring to the desired trigger pin 
on the 8-pin trigger connector centrally located 
above the terminal strip. 

 

•

  If using a Powerline Interface Modulator and 

powerline carrier devices, use the 
SA4120XM-1 cable (part of 4120TR Trigger 
Cable). See previous

 Powerline Carrier 

Device 

section. 

 

•

  If only using the on-board triggers, you can 

use a 4-wire cable (N4632-4, supplied with 
the control) as shown below. 

 

1

3

4

5

6

7

8

SA412OXM-1
CABLE

8-PIN TRIGGER CONNECTOR

KEY

00-trigcon-003-V1

+12 A

UX.

 

D

ATA

COM

SYNC

GND (-)

OUTPUT 17

(RED)

OUTPUT 18

(GREEN)

(ORANGE)

(YELLO

W)

(BLUE)

(PURPLE)

(BLA

CK)

 

Figure 11. On-Board Trigger Connector with 

SA4120XM-1 Cable for Use With X10 Powerline 

Interface Modulator

 

 

4-WIRE
CABLE

00-trigcon-005-V2

+12 A

UX.

 

GND (-)

OUTPUT 17

OUTPUT 18

(RED)

(YELLO

W)

(BLA

CK)

(GREEN)

1

3

4

5

6

7

8

8-PIN TRIGGER CONNECTOR

KEY

 

Figure 12. On-Board Trigger Connector with

 

4-Wire Cable for Trigger Use Only

 

Notes 

•

  There are two on-board triggers that can 

be used to activate output devices. 

•

  These outputs are normally high, and go 

low upon programmed condition.  

•

  The outputs can be programmed for 

inverted operation (normally low, go high) 
using *79 Menu mode. 

•

  Program these triggers using *80/*81 

Menu modes as you would for any other 
relay output. 

•

  When using these outputs, note: 

  pin 1 =  output number 17 (trigger 1): 
   

15 ohms to ground when closed 
(output low), open when off 
(output high, normal default); can 
be used to reset smoke detector 
power (must set “output normal 
low = yes” in *79 Menu mode, and 
set for zone type 54, fire zone 
reset, in *80 Menu mode); or can 
support 12V relay module

†

 that 

draws less than 100mA 

  pin 5 =  output number 18 (trigger 2): 
   

15 ohms to ground when closed 
(output low); open when off 
(output high, normal default); or 
can support 12V relay module 
that draws less than 20mA. 

 

 

NOTE: 

 Do not exceed 120mA combined 

current for both triggers. Doing so 
can damage PC board components 
and will void the system’s 
warranty. 

 

† e.g., Altronix AX-RBS in Canada 

 

 

 

 

Summary of Contents for ADEMCO Vista-12C

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands