Honeywell ADEMCO Vista-12C Installation And Setup Manual Download Page 75

Page: 75 / 112

5-19

*81 Menu Mode

PROMPT

VALID ENTRIES

EXPLANATION

Zone List No.

(00 = Quit)

Zone List Number

01-12 = zone list number
[

∗

] to continue

Enter the Zone List Number to program (or 00 to
end these entries). Press [

∗

] to advance.

In the following displays, zone list 01 has been
selected for programming.

01 Enter Zn Num.

(00 = Quit)

Zone Number

01-06, 9-24, 49-64 = zone

numbers followed by [

∗

] to

accept each zone

00 to continue

Enter each zone number to add to the zone list,
followed by pressing [

∗

] (example, 01

∗

, 02

∗

, 03

∗

After all zones are entered, press 00 to continue.

IMPORTANT:

Do not include fire zones in zone

lists that are used to STOP device actions.

01 Del Zn List?

0 = No 1 = Yes

Deleting Zone Lists

0 = don’t delete list
1 = delete this zone list
[

∗

] to continue

To delete the zone list, enter 1. All zones in the
zone list will be deleted automatically and the
system returns to the Zone List No. prompt.

To save the zone list, enter 0.

01 Delete Zone?

0 = No 1 = Yes

Deleting a Zone

0 = don’t delete zones
1 = go to next prompt to delete

zones

[

∗

] to continue

To save the entire zone list, enter 0 and the
system returns to the Zone List No. prompt.

To delete a zone or zones in a zone list enter 1 to
continue.

01 Zn to Delete?

(00 = Quit)

Delete the Zone

01-06, 9-24, 49-64 zones to be

deleted from list followed
by [

∗

] to accept each zone

00 to continue

Enter each zone to be deleted from the list,
followed by [

∗

]. After all zones to be deleted are

entered, enter 00 to return to the Zone List No.
prompt. so that another list can be programmed, if
desired.

Notes:

•

Any list may include any or all of the system's zone numbers.

•

A zone list can be assigned to more than one output relay.

•

When creating zone list 4 for linked zones, include only zones assigned to zone types 3, 4,

or 5. Do not include zones that have delays (entry/exit zones, interior w/delay) or 24-hour
zones, as these zone types may produce unpredictable operation and may not function as
intended.

Summary of Contents for ADEMCO Vista-12C
















































































































Search results

Summary of Contents for ADEMCO Vista-12C

Reviews:

Brands by name

Popular brands

Honeywell ADEMCO Vista-12C, Installation And Setup Manual

Search results

Summary of Contents for ADEMCO Vista-12C

Reviews:

Brands by name

Popular brands