manualshive.com logo in svg

Honeywell 15-0705-5, Component Maintenance Manual With Illustrated Parts List, Page: 77 / 113

Share
Download
Honeywell 15-0705-5 Component Maintenance Manual With Illustrated Parts List Download Page 77

COMPONENT MAINTENANCE MANUAL

15-0705

FITS AND CLEARANCES

1.

Planning Data

(TASK 33-30-15-99C-808-A01)

A.

Reason for the Job

(Subtask 33-30-15-99C-016-A01)

(1)

This section gives the fits and clearances used when the door mounted cargo loading light
was made.

B.

Job Setup Data

(Subtask 33-30-15-99C-017-A01)

(1)

The list that follows identifies Honeywell publications that are related to this section:

• ATA No. 20-00-03 (Pub. No. A09-1100-004), Standard Repair Procedures for Honeywell

Avionics Equipment Instruction Manual.

2.

Fits and Clearances

(TASK 33-30-15-220-801-A01)

A.

Fits and Clearances of the Door Mounted Cargo Loading Light

(Subtask 33-30-15-220-001-A01)

(1)

Refer to Table 8001 when you do the procedures in REPAIR (PGBLK 33-30-15-6000) and
ASSEMBLY (PGBLK 33-30-15-7000).

Table 8001. Fits and Clearances

Nomenclature/Description
Figure - Item

Requirement/Dimension

Lens lanyard - 50, IPL Figure 1

2.0 ± 0.10 inches (51 ± 2.5 mm) final length of lens lanyard, measured
between centers of terminal (62) eyelets

B.

Torque Values

(Subtask 33-30-15-220-002-A01)

(1)

Tighten nuts, bolts, screws, and tube fittings to standard torque values unless specified
differently in this manual. Refer to ATA No. 20-00-03 (Pub. No. A09-1100-004), Standard
Repair Procedures for Honeywell Avionics Equipment Instruction Manual, for standard torque
values.

EFFECTIVITY

ALL

33-30-15

Page 8001

30 Mar 2017

© Honeywell International Inc. Do not copy without express permission of Honeywell.

Summary of Contents for 15-0705-5


















































































































Reviews:

No comments