manualshive.com logo in svg

Honeywell 15-0705-5, Component Maintenance Manual With Illustrated Parts List, Page: 63 / 113

Share
Download
Honeywell 15-0705-5 Component Maintenance Manual With Illustrated Parts List Download Page 63

COMPONENT MAINTENANCE MANUAL

15-0705

REPAIR

1.

Planning Data

(TASK 33-30-15-99C-806-A01)

A.

Reason for the Job

(Subtask 33-30-15-99C-012-A01)

(1)

Use these procedures for the door mounted cargo loading light to replace defective parts and
replace or repair defective subassemblies.

(2)

Do only those procedures of DISASSEMBLY (PGBLK 33-30-15-3000) that are necessary to
make repairs. When new parts are necessary, refer to the ILLUSTRATED PARTS LIST (IPL
33-30-15-10000) for the correct part numbers and quantities.

B.

Job Setup Data

(Subtask 33-30-15-99C-013-A01)

(1)

You can use equivalent alternatives for the special tools, fixtures, equipment, and consumable
materials unless specified differently. The user must find equivalent alternatives.

(2)

Refer to Table 6001 for the specified special tools, fixtures, and equipment in this section.

(3)

CAGE codes and manufacturers’ addresses are available at https://cage.dla.mil.

Table 6001. Special Tools, Fixtures, and Equipment

Number

Description

Source

59250

crimping tool

CAGE: 00779

heat gun

commercially available

M22520/1-01

crimping tool

commercially available

M22520/1-02

positioner

commercially available

M81969/14-03

extraction/insertion tool

commercially available

WARNING:

BEFORE YOU USE A MATERIAL, REFER TO THE MANUFACTURERS’ MATERIAL
SAFETY DATA SHEETS. SOME MATERIALS CAN BE DANGEROUS.

CAUTION:

DO NOT USE MATERIALS THAT ARE NOT EQUIVALENT TO HONEYWELL
SPECIFIED MATERIALS. MATERIALS THAT ARE NOT EQUIVALENT CAN
CAUSE DAMAGE TO THE EQUIPMENT AND CAN MAKE THE WARRANTY NOT
APPLICABLE.

(4)

Refer to Table 6002 for the specified consumable materials in this section.

Table 6002. Consumables

Number

Description

Source

1132

alodine pen

commercially available

masking tape (0.75 inch (19.1 mm)
wide)

commercially available

A-A-59323

cleaning cloth (MIL-C-85043 Type
1)

commercially available

ANSI B74.18

aluminum oxide abrasive cloth
(600-grit)

commercially available

EFFECTIVITY

ALL

33-30-15

Page 6001

30 Mar 2017

© Honeywell International Inc. Do not copy without express permission of Honeywell.

Summary of Contents for 15-0705-5


















































































































Reviews:

No comments