manualshive.com logo in svg

Honeywell 15-0705-5, Component Maintenance Manual With Illustrated Parts List, Page: 42 / 113

Share
Download
Honeywell 15-0705-5 Component Maintenance Manual With Illustrated Parts List Download Page 42

COMPONENT MAINTENANCE MANUAL

15-0705

List of Acronyms and Abbreviations (Cont)

Term

Full Term

TR

temporary revision

U.S.A.

United States of America

USMS

United States Measurement System

VDC

volts direct current

6.

Process Verification

(TASK 33-30-15-99F-806-A01)

A.

Verification Data

(Subtask 33-30-15-99F-016-A01)

(1)

Honeywell does a verification of these technical instructions by performance or by simulation
of the necessary procedures. Performance shows that the procedures were checked by the
use of the manual. Simulation shows that the applicable personnel looked at the procedure
in the manual and that the procedure is technically correct. The dates of verification for
this manual are given in Table INTRO-3.

Table INTRO-3. Verification Data

Section

Method

Date

Testing and Fault Isolation

Performance

24 Feb 1994

Disassembly

Performance

24 Feb 1994

Assembly

Performance

24 Feb 1994

Engineering Technical Review

Performance

24 Feb 1994

7.

Software History

(TASK 33-30-15-99F-807-A01)

A.

Software Data

(Subtask 33-30-15-99F-017-A01)

(1)

Not applicable.

8.

History of Changes

(TASK 33-30-15-99F-808-A01)

A.

Modification/Configuration History

(Subtask 33-30-15-99F-018-A01)

(1)

Not applicable.

B.

Change History for Parts List

(Subtask 33-30-15-99F-019-A01)

(1)

Not applicable.

9.

Service Information Documents

(TASK 33-30-15-99F-809-A01)

A.

Applicable Service Information Documents

(Subtask 33-30-15-99F-020-A01)

(1)

Refer to Table INTRO-4 for other applicable service information documents not listed in
the Service Bulletin List.

EFFECTIVITY

ALL

33-30-15

Page INTRO-18

30 Mar 2017

© Honeywell International Inc. Do not copy without express permission of Honeywell.

Summary of Contents for 15-0705-5


















































































































Reviews:

No comments