Honeywell Home LTEM-PA Installation And Setup Manual Download Page 16

Page: 16 / 36

LTEM-P Installation and Setup Guide

DSC Control Panel Connections

This section applies to the following DSC PowerSeries (PC) control panels:

•

PC1616

•

PC1832

•

PC1864

1. Connect the control panel terminals labeled Black (

BLK

), Yellow (

YEL

), and Green (

GRN

) to the

communicator's

GND

, and

terminals respectively. See diagram below.

2. Connect the power adapter wires to the communicator's

PWR

and

GND

terminals as shown.

Observe polarity.

3. Refer to the control panel's installation manual for details on programming the control panel.

After reboot/power up, the communicator takes about 5-7 minutes to complete the scan
of the panel's partitions and zones. The control panel must be in the "Ready" state (no
alarms or faults) in order to perform the scan.

The communicator is powered
by the provided 9VDC Power
Adapter only.

Do not

connect

power from the control panel
to the communicator.

Connections for DSC PowerSeries Control Panels

Interlogix Control Panel Connections

This section applies to the following Interlogix NetworX (NX) Series control panels:

•

NX-8E

•

NX-4V2

•

NX-6V2

•

NX-8V2

1. Connect the control panel's

DATA

and

COM

terminals to the communicator's

and

GND

terminals respectively. See diagram below.

2. Connect the power adapter wires to the communicator's

PWR

and

GND

terminals as shown.

Observe polarity.

3. Refer to the control panel's installation manual for details on programming the control panel.

The communicator is powered
by the provided 9VDC Power
Adapter only.

Do not

connect

power from the control panel
to the communicator.

Connections for Interlogix NX Series Control Panels

Summary of Contents for LTEM-PA





































Search results

Summary of Contents for LTEM-PA

Reviews:

Brands by name

Popular brands

Honeywell Home LTEM-PA, Installation And Setup Manual

Search results

Summary of Contents for LTEM-PA

Reviews:

Brands by name

Popular brands