Honda CTX700A Owner'S Manual Download

Page: 38 / 141

n Gu

Start your engine using the following
procedure, regardless of whether the engine
is cold or warm.

NOTICE

•

If the engine does not start within 5 seconds, turn the
ignition off and wait 10 seconds before trying to start
the engine again for recovery of battery voltage.

•

Extended fast idling and revving the engine can
damage the engine, and the exhaust system.

•

Snapping the throttle or fast idling for more than about
5 minutes may cause exhaust pipe discolouration.

CTX700D

Make sure the engine stop switch is in the

(Run) position.

Turn the ignition switch to the ON position.

Check the transmission in Neutral (

indicator comes on).

Press the start button with the throttle
completely closed.

Make sure the parking brake lever is
released before riding.

❙

If Engine Does Not Start

(P34)

When you stop the engine

To stop the engine, put the transmission in
to Neutral (

indicator comes on).

If you turn the ignition switch to the OFF
position when the motorcycle in gear, the
engine will shut off with the clutch
disengaged.

Turn the ignition switch off.

Pull the parking brake lever when you park
the motorcycle.

14 CTX700-32MJF8000.book 35 ページ２０１３年５月９日　木曜日　午後９時５９分

Summary of Contents for CTX700A














































































































































Search results

Summary of Contents for CTX700A

Reviews:

Related manuals for CTX700A

Brands by name

Popular brands

Honda CTX700A, Owner'S Manual

Search results

Summary of Contents for CTX700A

Reviews:

Related manuals for CTX700A

Brands by name

Popular brands