Honda CTX700A Owner'S Manual Download

Page: 29 / 141

Instruments

(Continued)

n Gu

Display Setting

You can adjust the three settings.
• Backlight brightness adjustment
• Clock setting
•

Changing of speed and

mileage unit

In addition, to return to the ordinary display
at display setting.
• The button is not pressed for about 30

seconds

• Turn the ignition switch off and then on
Each setting will be cancelled if the A button
is not pressed.

1 Backlight brightness adjustment:

You can adjust the brightness to one of three
levels.

Turn the ignition switch to ON.

Press and hold the A button and B button until
the minute digit displays the brightness level.

Press the B button. The brightness is switched.

Press the A button. The backlight is set, and
then the display moves to the clock setting.

E type only

Ordinary display

Backlight brightness adjustment

Clock setting

Changing of speed and mileage unit

Press and hold the A button and B button

Press the A button

Except E type

Press the A button

E type only

Display setting

14 CTX700-32MJF8000.book 26 ページ２０１３年５月９日　木曜日　午後９時５９分

Summary of Contents for CTX700A














































































































































Search results

Summary of Contents for CTX700A

Reviews:

Related manuals for CTX700A

Brands by name

Popular brands

Honda CTX700A, Owner'S Manual

Search results

Summary of Contents for CTX700A

Reviews:

Related manuals for CTX700A

Brands by name

Popular brands