Honda CTX700A Owner'S Manual Download

Page: 109 / 141

Tyre Puncture

Removing Wheels

106

ou
bles

hoo

ting

Loosen the rear axle nut, lock nuts and
turn the adjusting nuts so the rear wheel
can be moved all the way forward for
maximum drive chain slack.

Remove the drive chain from the rear wheel
sprocket by pushing the rear wheel forward.

Remove the rear axle nut, washer A and
washer B.

Remove the rear axle shaft, washer B,
brake caliper bracket, rear wheel and side
collars.

Support the brake caliper assembly so
that it doesn’t hang from the brake
hose. Do not twist the brake hose.

Avoid getting grease, oil, or dirt on the
disc to pad surfaces.

Do not push the brake pedal while the
wheel is removed.

Do not pull the parking brake lever
while the wheel is removed.

CTX700D only

Pulser ring

Lock nut

Adjusting nut

Right side
collar

Washer B

Rear axle nut

Washer A

Wheel speed sensor

Rear axle shaft

Lock nut

Drive
chain

Washer B

Adjusting nut

Left side collar

14 CTX700-32MJF8000.book 106 ページ２０１３年５月９日　木曜日　午後９時５９分

Summary of Contents for CTX700A














































































































































Search results

Summary of Contents for CTX700A

Reviews:

Related manuals for CTX700A

Brands by name

Popular brands

Honda CTX700A, Owner'S Manual

Search results

Summary of Contents for CTX700A

Reviews:

Related manuals for CTX700A

Brands by name

Popular brands