Honda CRF300L Manual Download Page 22

Page: 22 / 125

Loading

●

Carrying extra weight affects your vehicle's

handling, braking and stability.

Always ride at a safe speed for the load you

are carrying.

●

Avoid carrying an excessive load and keep

within specified load limits.

Maximum weight capacity / Maximum

luggage weight

P. 120

●

Tie all luggage securely, evenly balanced

and close to the centre of the vehicle.

●

Do not place objects near the lights or the

muffler.

Also follow these guidelines when you ride off-

road on rough terrain:

●

Do not carry a passenger.

●

Keep cargo small and light weight.

Make sure it cannot easily be caught on

brush or other objects, and that it does not

interfere with your ability to shift position to

maintain balance and stability.

WARNING

Overloading or improper loading can

cause a crash and you can be seriously

hurt or killed.

Follow all load limits and other loading

guidelines in this manual.

20200914163746_32K1TB000_eng_BOOK Page 22 Monday, September 14 2020 16:42:25 JST

Loading

Vehicle Safety

Summary of Contents for CRF300L






























































































































Search results

Summary of Contents for CRF300L

Reviews:

Related manuals for CRF300L

Brands by name

Popular brands

Honda CRF300L, Manual

Search results

Summary of Contents for CRF300L

Reviews:

Related manuals for CRF300L

Brands by name

Popular brands