Honda CRF300L Manual Download Page 19

Page: 19 / 125

Turn the handlebar fully to the left.

Turning the handlebar to the right

reduces stability and may cause the

vehicle to fall.

Turn the ignition switch to the (Lock)

position and remove the key.

P. 46

Refuelling and Fuel Guidelines

Follow these guidelines to protect the engine,

fuel system and catalytic converter:

●

Use only unleaded petrol.

●

Use recommended octane number. Using

lower octane petrol will result in decreased

engine performance.

●

Do not use fuels containing a high

concentration of alcohol.

P. 118

●

Do not use stale or contaminated petrol or

an oil/petrol mixture.

●

Avoid getting dirt or water in the fuel tank.

20200914163746_32K1TB000_eng_BOOK Page 19 Monday, September 14 2020 16:42:25 JST

Riding Precautions

Vehicle Safety

Summary of Contents for CRF300L






























































































































Search results

Summary of Contents for CRF300L

Reviews:

Related manuals for CRF300L

Brands by name

Popular brands

Honda CRF300L, Manual

Search results

Summary of Contents for CRF300L

Reviews:

Related manuals for CRF300L

Brands by name

Popular brands