Honda CRF300L Manual Download Page 33

Page: 33 / 125

Fuel consumption

Displays the fuel consumption since the

selected tripmeter was reset.

The fuel consumption will be calculated

based on value displayed on the tripmeter (A

or B) selected.

Also, the fuel consumption for tripmeter A

will be displayed when the odometer,

tripmeter A, and stopwatch are selected.

Display range:

ED type

0.0 to 299.9 L (litres) or 0.0 to 299.9

gal (gallon)

Except ED type

0.0 to 299.9 L (litres)

•

ED type

More than 299.9 L (litres) or

299.9 gal (gallon): “299.9” is displayed.

•

Except ED type

More than 299.9 L (litres):

“299.9” is displayed.

When “---.-” is displayed, go to your dealer

for service.

To reset the fuel consumption:

(

P.26

)

20200914163746_32K1TB000_eng_BOOK Page 33 Monday, September 14 2020 16:42:25 JST

Operation Guide

Instruments

(Continued)

Summary of Contents for CRF300L






























































































































Search results

Summary of Contents for CRF300L

Reviews:

Related manuals for CRF300L

Brands by name

Popular brands

Honda CRF300L, Manual

Search results

Summary of Contents for CRF300L

Reviews:

Related manuals for CRF300L

Brands by name

Popular brands