Honda CRF300L Manual Download Page 44

Page: 44 / 125

Indicators

20200914163746_32K1TB000_eng_BOOK Page 44 Monday, September 14 2020 16:42:25 JST

Operation Guide

Continued

Comes on when the

transmission is in Neutral.

Comes on briefly when the ignition switch is turned to the (On) position with the engine

stop switch in the (Run) position.

FO, U type

If it comes on while engine is running:

(

P.96

)

Neutral indicator

PGM-FI (Programmed Fuel Injection)

malfunction indicator lamp (MIL)

If one of these indicators does not come on when it should, have your dealer

check for problems.

Rear ABS (Anti-lock Brake System) OFF indicator

Comes on briefly when the ignition switch is turned to the (On) position.
Comes on when the ABS function on the rear wheel is turned off.

ED, KO type

If it comes on or flashes while engine is running:

(

P.96

)

Summary of Contents for CRF300L






























































































































Search results

Summary of Contents for CRF300L

Reviews:

Related manuals for CRF300L

Brands by name

Popular brands

Honda CRF300L, Manual

Search results

Summary of Contents for CRF300L

Reviews:

Related manuals for CRF300L

Brands by name

Popular brands