Honda CRF300L Manual Download Page 12

Page: 12 / 125

RADIATOR CAP LABEL

DANGER

Except KO type

NEVER OPEN WHEN HOT.

Hot coolant will scald you.

Relief pressure valve begins to open at

1.1 kgf/cm

ACCESSORIES AND LOADING WARNING LABEL

WARNING

ED type

ACCESSORIES AND LOADING

•

The safety stability and handling of this vehicle may be

affected by the addition of accessories and luggage.

•

Read carefully the instructions contained in user's manual

and installation guide before installing any accessory.

•

The total weight of accessories and luggage added to rider's

and passenger's weight should not exceed

162 kg (357 lb)

which is the maximum weight capacity.

•

The luggage weight must not exceed

4.5 kg (10 lb)

under

any circumstances.

•

The fitting of large fork-mounted or large handlebar

mounted fairing is not recommended.

20200914163746_32K1TB000_eng_BOOK Page 12 Monday, September 14 2020 16:42:25 JST

Image Labels

Vehicle Safety

Continued

Summary of Contents for CRF300L






























































































































Search results

Summary of Contents for CRF300L

Reviews:

Related manuals for CRF300L

Brands by name

Popular brands

Honda CRF300L, Manual

Search results

Summary of Contents for CRF300L

Reviews:

Related manuals for CRF300L

Brands by name

Popular brands