Honda CRF300L Manual Download Page 123

Page: 123 / 125

Specifications

■

Main Components

Overall length

2,230 mm (87.8 in)

Overall width

820 mm (32.3 in)

Overall height

1,200 mm (47.2 in)

Wheelbase

1,455 mm (57.3 in)

Minimum ground

clearance

285 mm (11.2 in)

Caster angle

Except KO

type

27° 30’

KO type

27.5°

Trail

109 mm (4.3 in)

Curb weight

ED type

142 kg (313 lb)

FO type

141 kg (311 lb)

KO, U type

140 kg (309 lb)

Maximum weight

capacity

ED type

162 kg (357 lb)

FO type

155 kg (342 lb)

KO type

139 kg (306 lb)

U type

149 kg (328 lb)

Maximum luggage

weight

ED type

4.5 kg (10 lb)

Passenger capacity

Rider and 1 passenger

Minimum turning

radius

Except KO

type

2.20 m (7.2 ft)

KO type

2.3 m (7.5 ft)

Displacement

286 cm

(17.4 cu-in)

Bore x stroke

76.0 x 63.0 mm (2.99 x 2.48 in)

Compression ratio

10.7:1

Fuel

Unleaded petrol
Recommended: 91 RON or higher

Fuel containing

alcohol

ETHANOL up to 10 % by volume

Tank capacity

7.8 L (2.06 US gal, 1.72 Imp gal)

Battery

YTZ8V
12 V-7.0 Ah (10 HR) / 7.4 Ah (20 HR)

Gear ratio

1st

3.538

2nd

2.250

3rd

1.650

4th

1.346

5th

1.115

6th

0.925

Reduction ratio

(primary / final)

2.807 / 2.857

*1 : Including rider, passenger, all luggage, and accessories.

*2 : Includes the weight of the luggage and added accessories.

20200914163746_32K1TB000_eng_BOOK Page 123 Monday, September 14 2020 16:42:25 JST

Specifications

120

Summary of Contents for CRF300L






























































































































Search results

Summary of Contents for CRF300L

Reviews:

Related manuals for CRF300L

Brands by name

Popular brands

Honda CRF300L, Manual

Search results

Summary of Contents for CRF300L

Reviews:

Related manuals for CRF300L

Brands by name

Popular brands