manualshive.com logo in svg

Honda 2003 ACCORD 4 DOOR, Installation Instructions Manual

Share
Download
Honda 2003 ACCORD 4 DOOR Installation Instructions Manual Download Page 23

© 2003 American Honda Motor Co., Inc - All Rights Reserved.

AII 24378 (0303)

23 of 24

2527131M

4 x 8 mm
WASHER SCREWS (4)

FRONT UNIT
BRACKET

REAR UNIT
BRACKET

RECEIVER
UNIT

4 mm FLANGE
NUTS (4)

2621031M

CUSHION TAPES (2)

PANEL HOLE

ANTENNA CABLE
AND DIN CABLE

WIRE TIE
WITH CLIP

CUSHION
TAPES

2621020M

6 x 12 mm
WASHER-BOLTS (3)

DRILLED HOLES (3)

RECEIVER UNIT

78. Install the front and rear unit brackets to the

receiver unit using two 4 x 8 mm washer-screws
and two 4 mm flange nuts for each bracket.

79. Position the receiver unit between the right trunk

side panel and the rear fender panel, and plug in
the antenna cable connectors, the DIN cable
connector, and the XM radio harness connector
using the panel hole to access the receiver unit.

80. Attach the receiver unit to the body panel using

three 6 x 12 mm washer-bolts. Tighten the bolts
securely.

81. Attach two cushion tapes to the edges of the

panel in the areas shown.

82. Inside the fender area, bundle up the excess

antenna cable and DIN cable, and secure them
with one wire tie with clip to the hole in the rear
unit bracket.

83. Wrap the ends of the antenna cable and the DIN

cable with two cushion tapes.

2621010M

ANTENNA CABLE

DIN CABLE

XM RADIO
HARNESS

RECEIVER
UNIT

FENDER
PANEL

RIGHT TRUNK
SIDE PANEL

PANEL HOLE

Summary of Contents for 2003 ACCORD 4 DOOR

























Reviews:

No comments

Brands by name

Popular brands

Load more brands