manualshive.com logo in svg

Honda 2003 ACCORD 4 DOOR, Installation Instructions Manual

Share
Download
Honda 2003 ACCORD 4 DOOR Installation Instructions Manual Download Page 22

22 of 24

AII 24378 (0303)

© 2003 American Honda Motor Co., Inc - All Rights Reserved.

73. Secure the antenna cable, the DIN cable, and the

XM radio harness with three wire ties with clips.
Insert the clips on the wire ties into the panel
holes.

74. Using scissors, cut out the shaded areas from the

template.

75. Position the template on the right trunk side panel,

and tape the template in place. While wearing eye
protection, center punch the three cross marks on
the template.

76. Remove the template. Place a shop towel on the

inside of the right trunk side panel to collect any
metal shavings.

2527100M

TEMPLATE

Cut
(shaded areas)

2620050M

ANTENNA
CABLE

RADIO
HARNESS

WIRE TIES WITH CLIPS (3)

2527110M

CENTER PUNCH

TEMPLATE

MASKING
TAPE

RIGHT TRUNK
SIDE PANEL

CROSS MARKS (3)

2527121M

VINYL TAPE

8 mm DRILL BIT

10 mm

SHOP
TOWEL

DIN CABLE

ANTENNA
CABLE

77. Drill three 8 mm holes through the inner panel:

•

Wrap vinyl tape around the drill bit 10 mm from
the end, or attach a drill stop.

•

While wearing eye protection, drill an 8 mm
hole through each center-punched mark.

•

Remove all burrs and metal shavings, and
apply touch-up paint to the edges of each
drilled hole.

•

Remove and discard the shop towel.

Summary of Contents for 2003 ACCORD 4 DOOR

























Reviews:

No comments

Brands by name

Popular brands

Load more brands