manualshive.com logo in svg

Homentry HESD01, Installation And Operating Instructions Manual, Page: 4 / 20

Share
Download
Homentry HESD01 Installation And Operating Instructions Manual Download Page 4

4

INTRODUCTION

CARTON INVENTORY

2

1. 

Opener / powerhead

2. 

HE952 hand held trsansmitter (2)

3. 

Curved door arm

4. 

Hanging bracket (2)

5. 

Rail bracket (2)

6. 

Lintel bracket

7. 

Door bracket

8. 

Hardware bag

9. 

Rail assembly (chain)

10. 

Manual

11. 

Warning labels

12. 

Rail centre bracket

13. 

Rail mounting bracket

1

2

3

4

5

6

7

8

9

11

10

OwnersCopy:SAVETHESEINSTRUCTIONSforfuturereference

MT50EVO

SectionalGarageDoorOpener

InstallationandOperatingInstructions

ThismanualcontainsIMPORTANTSAFETYinformation

DONOTPROCEED WIT

HTHEINSTALLA

TIONBEFOREREADINGTHO

ROUGHLY

N2966

N2966

N2966

N2966

gomerlin.com.au

gomerlin.co.nz

Manual

12

114A3361

For Service Call

Installation Date

132A2900

RISK OF ENTRAPMENT

Repeat Safety Reverse Test monthly. Door

must reverse on contact with a 40mm obstacle

placed on the floor. Make necessary adjustments.
AUTOMATIC DRIVE:

Keep away from the area of the door since it may

operate unexpectedly.
EMERGENCY RELEASE:

To release, pull down firmly on the red handle.

    

13

RAIL DIMENSIONS

NOTE: 

The Ceiling Fixing Point is measured back from the lintel (see item 6 to 7 of “completed installation”). Also allow 300 mm 

back from the fixing point for installation of the powerhead (item 7 to 9 of “completed installation”).

3

DOOR HEIGHT: 

Sectional Doors

RAIL LENGTH:

CEILING FIXING POINTS:

OVERALL LENGTH:

Up to 2.2 m

3000 mm segmented

2840 mm

3150 mm

Your garage door opener and rail are packed in a single carton. 

Summary of Contents for HESD01





















Reviews:

No comments