background image

17

MAINTAINENCE AND CARE OF YOUR OPENER

USING YOUR OPENER

24

1. 

Your opener can be activated by any of the following devices:

• 

Opener control panel: 

Up and Down Buttons and Green 

O.S.C.

• 

The Outside Keyswitch or Keyless Entry System

 (if you 

have installed either of these accessories).

• 

The Transmitter.

 Hold the push button down until the door 

starts to move.

2. 

Opening the Door Manually: Door should be fully closed 

if possible. Weak or broken springs could allow an open 

door to fall rapidly. Property damage or serious personal 

injury could result.

NOTE: For full instructions on how to operate the door 

manually refer to section 18.

The door can be opened manually by pulling the release handle 

down. To reconnect the door, press the Green button in the 

centre of the trolley assembly.

Do not use the manual release handle to pull the door open 

or closed.

3. 

When the Opener is Activated by Transmitter:

• 

If open, the door will close. If closed, the door will open.

• 

If closing, the door will stop.

• 

If opening, the door will stop (allowing space for entry and 

exit of pets and for fresh air).

• 

If the door has been stopped in a partially open or closed 

position, it will reverse direction.

• 

If an obstruction is encountered while closing, the door will 

reverse to the UP limit.

• 

If an obstruction is encountered while opening, the door will 

stop and briefly reverse.

• 

The optional Protector System™ (IR Beams) uses an 

invisible beam which, when broken by an obstruction, causes 

a closing door to open and prevents an open door from 

closing. It is STRONGLY RECOMMENDED for homeowners 

with young children.

4. 

The opener lights will turn on under the following 

conditions: 

When the opener is initially plugged in; when 

power is restored after interruption or when the opener is 

activated. 

Lights will turn off automatically after 2-1/2 minutes.

CARE OF YOUR OPENER

25

Once a Month

• 

Manually operate door. If it is unbalanced or binding, call a 

qualified door technician.

• 

Check to be sure door opens & closes fully. Adjust limits and/

or force if necessary.

• 

Repeat the safety reverse test. Make any necessary 

adjustments.

Once a Year

• 

Lightly grease the belt and inside the rail assembly where the 

trolley slides.

• 

Internally the opener does not require additional lubrication.

• 

Lightly grease the belt and inside the rail assembly where the 

trolley slides. Be careful to use gloves around any sharp 

metal edge or the rail.

REPLACE BATTERIES IN TRANSMITTERS

26

Battery of the transmitter:

The batteries in the transmitter have an extremely long life. If the 

transmission range decreases, the batteries must be replaced. 

Batteries are not covered by the warranty.

WARNING! The wireless transmitters 

contain button/coin cell batteries.

• 

The battery is hazardous.

• 

Keep new and used batteries away 

from children.

• 

Do not ingest battery. Chemical burn 

hazard.

• 

If the coin cell battery is swallowed or 

placed inside any part of the body, it can 

cause severe or fatal injuries in 2 hours or 

less.

• 

If the battery compartment does not close securely, 

stop using the product and keep away from 

children.

• 

If you think batteries might have been swallowed or 

placed inside any part of the body, call the 24-hour 

Poisons Information Centre on 13 11 26 in 

Australia, or the 24-hour National Poisons Centre 

on 0800 764 766 in New Zealand, or seek immediate 

medical attention.

• 

Dispose of used coin/button cell batteries 

immediately and safely. Flat batteries can still be 

dangerous.

Replacing battery (CR2032):

To replace battery, turn transmitter around and open the case 

with a screwdriver. Lift cover and lift control board below. Slide 

battery to one side and remove. Observe polarity of battery!
Assemble again in reverse direction.

Summary of Contents for HESD01





















Reviews: