Homentry HESD01 Installation And Operating Instructions Manual Download Page 18 | Manualshive

Page: 18 / 20

Homentry HESD01 Installation And Operating Instructions Manual Download Page 18

18

SPECIFICATIONS

SPECIFICATIONS - HOMENTRY - HESD01

27

Input Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Max. Pull Force. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Max. door weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Max. lift under spring tension. . . . . . . . . . . . . . . . . . . . . . . .
Max. door area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Motor

Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Noise level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Drive Mechanism

Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Length of Travel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LED light. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Light on Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Door Linkage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety

Personal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electronic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Limit Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limit Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Soft-start/Soft-stop

Dimensions

Length (Overall). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headroom Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hanging Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Receiver

Memory Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

220-240 Vac, 50 - 60 Hz
475 N
80 Watt
4 Nm
60 kg
15 kg
Sectional door 10.5m

2

DC gearmotor permanent lubrication
54 db at 1 metre

Chain with one-piece troley on steel rail
2.2 m
8 LEDs
3 min

Adjustable door arm. Pull cord trolley release

Push button stop in

UP and DOWN

direction. Automatic

safety reverse in both

UP and DOWN

direction

Automatic force adjustment
Transformer overload protector and low voltage push button

wiring
Mechanical Passpoint/RPM sensor
Electronic

3.15 m
32 mm
10 kg

16 handset codes. 1 keypad code
433.30/433.92/434.54 MHz

«
...
16
17
18
19
20
»

Summary of Contents for HESD01





















Reviews:

No comments