background image

Holtkamp Electronics UNO 7600XL engl.                        techn. Stand 04.2016                                              4050_04.2016 V09.2019

- 24 -

Display shows

Factory setting

Description

Token counter

The token counter offers the possibility, to install a further counter, which counts 

separately the inserted token. (Else the amounts are added to the cash coun

-

ter). There  is  the  possibility  to  activate  2  token. These  indicate  the  value  of 

the EMP channel 5 and 6 to the token counter 5 and 6. Please notice that the 

channel 6 of the EMP is equipped for Holtkamp token. Channel 5 is therefore 

for your own token equipped. 

If you liked to use own tokens, our electronic coin tester must be pro-

grammed on these coins. Please absolutely to specify by your order!

Token impuls 

counter 5

no

 

● If “yes” is set up, in the statistic menu will be shown the daily token coun-

 

      ter and total token counter. The value of token has to be set up under the 

 

      menu item “coin tester valuing channel 5”. Factory setting is value “0”.

 

● If “no” I set, the token counter is deactivated.

Token impuls 

counter 6

no

 

● If “yes” is set up, in the statistic menu will be shown the daily token counter 

 

      and total token counter. The value of the token is on “3,5” factory set up 

 

        and is put out to channel 6 on EMP. If you want to change the value of the  

     Holtkamp token, you will have to set it up from menu item “coin tester 

 

      valuing”.

 

● If “no” I set, the token counter is deactivated.

Daily counter 

yes

The daily counter setting offers the possibility to display all the daily counters 

in the statistic menu or not.

 

● If “yes” is set, all available daily counters will be displayed.

 

● If “no” is set no daily counters will be displayed. 

3 digits main time

no

The 3 digits main time offers the possibility to show the main time in 2 or 3 digits 

on the display. 

 

● If “no” is set, main time will be displayed in 2 digits and so limited to 99 min 

 

     or 1 hour 39 min.

 

● If “yes” is set, the main time will displayed in 3 digits.

Memory lock 

no

The memory lock offers the possibility to obviate the repeated sale of main time.

 

● If “yes” is set the main time can be bought only once.

 

● If “no” is set, can the main time repeatable sold.

Mains failure

fuse

The mains failure fuse offers the possibility that the main time remains even 

after a mains failure. After the mains supply is restored again, the devices with 

the stored main time will be switched back on, per random time generator, to 

prevent a mains overload.

 

● If “yes” is set, the same main times and prices apply irrespective if pay-

 

     ment is made cash or by card.

 

● If “no” is set, differing main times and prices will set for payment cash or 

 

     by card.

Summary of Contents for UNO 7600/XL





































Reviews: