background image

 

 

TLR-D5 Engineering Manual

 

TLR-D5  
Intelligent Fan Coil controller, Base & Terminal 

 
Features 

 

Temperature control for 2 and 4-pipe fan coil systems.  

 

Relays switching for each up to 10(6)A 

 

Large temperature range from  
–20°C to 70°C (-4°F to 158°F). 

 

Automatic fan control for three stage fans.  

 

Control for heating, cooling and fan only operation 

 

Cost saving option with Economy functionality and set point limitation 

 

Password protected programmable user and control parameters 

 

External sensor or open contact for remote control, external heat – cool change or auto-changeover on supply 
or outdoor temperature with selectable activation limits One terminal may control up to 8 base units in 
parallel mode 

 

Password protected programmable user and control parameters 

o

 

Setpoint range limitation 

o

 

Access control for setpoints, fan speeds and mode change 

o

 

Access control for heat/cool change and time programs 

o

 

Select your display contents 

o

 

Selectable behavior after return from power failure 

 

Temperature display in degree Celsius or Fahrenheit 

Deluxe Version: 

o

 

Clock and time schedule functions with special options for schools and universities 

o

 

Clock keeps running for 48h in case of power failure 

o

 

Display with blue backlight 

o

 

Infrared remote controller option:  
With special features for Boost and delayed switching on or off 

Applications 

 

Air Only Systems: Three stage fans for single duct systems. 

 

Air/Water Systems: Induction units, fan coil units for 4-pipe systems 

General Description 

The TLR-D5 is a stand-alone electronic single loop controller with a fan control option and a binary sequence. The 
controller includes 1 NTC room temperature sensor and 3+2 relays outputs. A detailed adaptation to local conditions is 
possible with the use of a simple configuration routine. The TLR-D5 can be configured using the standard operation 
terminal. No special tools or software is required.  
The TLR-D5 has been specifically developed to switch larger fans with switching power of up to 10 (6) A.  

Doc: 70-00-0095 20081223 

©2008 Vector Controls 

Page 1 

SUNSTAR传感与控制 http://www.sensor-ic.com/ TEL:0755-83376549 FAX:0755-83376182 E-MAIL:[email protected]

SUNSTAR自动化 http://www.sensor-ic.com/ TEL: 0755-83376489 FAX:0755-83376182 E-MAIL:[email protected]

Summary of Contents for TLR-D5















Reviews: