Holtek BS86DH12C Manual Download Page 93

Page: 93 / 192

Rev. 1.00

October 26, 2018

Rev. 1.00

October 26, 2018

BS86DH12C

High Voltage Touch A/D Flash MCU with HVIO

BS86DH12C

High Voltage Touch A/D Flash MCU with HVIO

Bit 3

PTOC

: PTM PTP output control

Compare Match Output Mode

0: Initial low

1: Initial high

PWM Output Mode/Single Pulse Output Mode

0: Active low

1: Active high

This is the output control bit for the PTM output pin. Its operation depends upon

whether PTM is being used in the Compare Match Output Mode or in the PWM

Output Mode/Single Pulse Output Mode. It has no effect if the PTM is in the Timer/

Counter Mode. In the Compare Match Output Mode it determines the logic level of

the PTM output pin before a compare match occurs. In the PWM Output Mode it

determines if the PWM signal is active high or active low. In the Single Pulse Output

Mode it determines the logic level of the PTM output pin when the PTON bit changes

from low to high.

Bit 2

PTPOL

: PTM PTP output polarity control

0: Non-invert

1: Invert

This bit controls the polarity of the PTP output pin. When the bit is set high the PTM

output pin will be inverted and not inverted when the bit is zero. It has no effect if the

PTM is in the Timer/Counter Mode.

Bit 1

PTCAPTS

: PTM capture trigger source selection

0: From PTPI pin

1: From PTCK pin

Bit 0

PTCCLR

: PTM counter clear condition selection

0: Comparator P match

1: Comparator A match

This bit is used to select the method which clears the counter. Remember that the

Periodic TM contains two comparators, Comparator A and Comparator P, either of

which can be selected to clear the internal counter. With the PTCCLR bit set high,

the counter will be cleared when a compare match occurs from the Comparator A.

When the bit is low, the counter will be cleared when a compare match occurs from

the Comparator P or with a counter overflow. A counter overflow clearing method can

only be implemented if the CCRP bits are all cleared to zero. The PTCCLR bit is not

used in the PWM Output, Single Pulse Output or Capture Input Mode.

• PTMDL Register

Bit

Name

R/W

POR

Bit 7~0

D7~D0

: PTM Counter Low Byte Register bit 7 ~ bit 0

PTM 10-bit Counter bit 7 ~ bit 0

• PTMDH Register

Bit

Name

—

R/W

—

POR

—

Bit 7~2

Unimplemented, read as “0”

Bit 1~0

D9~D8

: PTM Counter High Byte Register bit 1 ~ bit 0

PTM 10-bit Counter bit 9 ~ bit 8

Summary of Contents for BS86DH12C

































































































































































































Search results

Summary of Contents for BS86DH12C

Reviews:

Holtek BS86DH12C, Manual, Page: 93 / 192

Search results

Summary of Contents for BS86DH12C

Reviews: