manualshive.com logo in svg

Holtek BS86DH12C, Manual, Page: 162 / 192

Share
Download
Holtek BS86DH12C Manual Download Page 162

Rev. 1.00

162

October 26, 2018

Rev. 1.00 

163

October 26, 2018

BS86DH12C

High Voltage Touch A/D Flash MCU with HVIO

BS86DH12C

High Voltage Touch A/D Flash MCU with HVIO

interrupt vector address, the global interrupt enable bit, EMI, and the Serial Interface Interrupt 
enable bit, IICE, must first be set. When the interrupt is enabled, the stack is not full and any of the 
above described situations occurs, a subroutine call to the respective Interrupt vector, will take place. 
When the interrupt is serviced, the Serial Interface Interrupt flag, IICF, will be automatically cleared. 
The EMI bit will also be automatically cleared to disable other interrupts.

UART Transfer Interrupt

The UART Transfer Interrupt is controlled by several individual UART transfer conditions. When 
one of these conditions occurs, an interrupt pulse will be generated to get the attention of the 
microcontroller. These conditions are a transmitter data register empty, transmitter idle, receiver data 
available, receiver overrun, address detect and an RX pin wake-up. To allow the program to branch 
to the respective interrupt vector addresses, the global interrupt enable bit, EMI, and the UART 
interrupt enable bit, URE, must first be set. When the interrupt is enabled, the stack is not full and 
any of these conditions are created, a subroutine call to the UART Interrupt vector, will take place. 
When the UART Interrupt is serviced, the UART Interrupt flag, URF, will be automatically cleared. 
The EMI bit will also be automatically cleared to disable other interrupts. However, the USR register 
flags will only be cleared when certain actions are taken by the UART, the details of which are given 
in the UART Interfaces chapter.

LVD Interrupt

The Low Voltage Detector Interrupt is an individual interrupt source with its own interrupt vector. 
An LVD Interrupt request will take place when the LVD Interrupt request flag, LVF, is set, which 
occurs when the Low Voltage Detector function detects a low power supply voltage. To allow the 
program to branch to its respective interrupt vector address, the global interrupt enable bit, EMI, 
and Low Voltage Interrupt enable bit, LVE, must first be set. When the interrupt is enabled, the stack 
is not full and a low voltage condition occurs, a subroutine call to the relevant interrupt vector will 
take place. When the Low Voltage Interrupt is serviced, the LVF flag will be automatically cleared. 
The EMI bit will also be automatically cleared to disable other interrupts.

A/D Converter Interrupt

The A/D Converter Interrupt is controlled by the termination of an A/D conversion process. An A/D  
Converter Interrupt request will take place when the A/D Converter Interrupt request flag, ADF, is 
set, which occurs when the A/D conversion process finishes. To allow the program to branch to its 
respective interrupt vector address, the global interrupt enable bit, EMI, and A/D Interrupt enable bit, 
ADE, must first be set. When the interrupt is enabled, the stack is not full and the A/D conversion 
process has ended, a subroutine call to the A/D Converter Interrupt vector will take place. When the 
interrupt is serviced, the A/D Converter Interrupt flag, ADF, will be automatically cleared. The EMI 
bit will also be automatically cleared to disable other interrupts.

EEPROM Interrupt

The EEPROM Write Interrupt is an individual interrupt source with its own interrupt vector. An 
EEPROM Write Interrupt request will take place when the EEPROM Write Interrupt request flag, 
DEF, is set, which occurs when an EEPROM Write cycle ends. To allow the program to branch to 
its respective interrupt vector address, the global interrupt enable bit, EMI, and EEPROM Write 
Interrupt enable bit, DEE, must first be set. When the interrupt is enabled, the stack is not full and an 
EEPROM Write cycle ends, a subroutine call to the respective interrupt vector will take place. When 
the EEPROM Write Interrupt is serviced, the DEF flag will be automatically cleared and the EMI bit 
will also be automatically cleared to disable other interrupts.

Summary of Contents for BS86DH12C

































































































































































































Reviews:

No comments